Assessments - 3, GPA: 4 ( )

Fabricante : Hitachi Arquivo Tamanho: 5.43 mb Arquivo Nome : Língua de Ensino:

For example, POWER and PLAY may be learned, but other functions may not • The signal from the remote control may not be strong enough. Insert fresh batteries and try Learning again. 9. You have forgotten your V-Chip pass code. • See Appendix A, Bypassing the V-Chip Lock. 10. Lamp indicator light is a constant red. • Turn the TV off for at least 2 minutes. Turn back on. If light is still red, the lamp has failed. Replace it. See Appendix H for lamp replacement information. 11. Lamp indicator light is a constant yellow. • Lamp may fail soon. Purchase a new lamp. See Appendix H for lamp replacement information. 12. Lamp indicator light is a flashing yellow. • Lamp cover door is open or lamp cartridge is not secure. See Appendix H for lamp replacement information. 13. Status indicator light is a constant yellow. • Room temperature has exceeded proper levels. Cool the room. 14. Status indicator light is a constant/flashing red. • Service is required. Contact your dealer or a Mitsubishi Authorized Service Center to arrange for a service evaluation. Listings of Mitsubishi Authorized Service locations can be obtained from our web site, or by calling 1-800-332-2119. 15. PIP does not display a picture. • Make sure the V-Chip lock is off. • Not all inputs can be displayed as a PIP. 16. Digital channels do not appear in PIP. • Normal PIP operation. 17. The sound does not match the screen picture. • NetCommand® is set up incorrectly. • The TV’s “Listen to:” setting may be set to SAP. • If using stereo or A/V receiver speakers, check their input selection. • If using stereo or A/V receiver, check that AUDIO OUTPUT on TV’s back panel is connected to the A/V receiver. 18. There is a large black or gray rectangle on the screen. • The TV’s analog closed captioning has been set to “text” mode in the Captions menu. Turn off because there is no text information being broadcast. 19. You cannot see a picture when playing a VHS tape. • Display the Device Selection menu and select the correct VCR. • Check your VCR’s owner’s guide for further troubleshooting. 20. V-Chip is not working. • Make sure that V-Chip is On. • If V-Chip Hours are currently set to disable the V-Chip lock, the V-Chip will not block programming. 21. The TV will not turn on after being plugged in. • If green light on front panel is blinking, wait for at least one minute for the light to turn off, then press Power again. 22. TV functions do not respond to the remote control or to front panel control and will not Power Off. • Use the System Reset button . 23. Name options not available for some channels. • Only memorized analog channels can be named. 24. When viewing a stopped VCR, white lines are rolling on the screen. • Turn off video mute for the VCR. • Begin playing the tape. • Change the VCR input to the antenna input. 25. TV turned itself Off and the light on the front panel started to blink. • Momentary power fluctuation caused the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn On again. • If the TV does not stay turned On, use the System Reset button. If this happens frequently, obtain an AC line power conditioner/surge protector. • An unusual digital signal may have been received, triggering a protection circuit. Wait for the light to stop flashing and turn TV on. 26. When a device is selected from the Device Selection menu, the screen is blue (no signal source). • Make sure the selected device is turned on. • From the Edit NetCommand® menu select Review setting. Verify that the inputs are actually connected to the TV . If they are not, either change the physical connections on the back panel, or select the Change setting on the Edit NetCommand menu to change the TV NetCommand’s settings for the connection. • Begin play of the VCR. 27. The device does not respond to button presses from the remote. • Remote has not been set up for NetCommand® use. • The incorrect manufacturer was selected during setup. Select the Change setting from the Setup menu and then the device to display the manufacturer selection. Change if necessary. • The device is not supported and keys have not been learned. • The requested function is not supported by NetCommand. Verify that the function is supported or keys are learned. • The IR emitter is incorrectly placed. Make sure the IR emitter is facing the IR sensor in the device. • The IR emitter is not plugged into the IR emitter Output NetCommand. • The IR emitter is facing the TV screen, causing double signals. Be sure that the IR emitter cannot send to the TV. 28. The A/V Receiver is the selected audio source but there is no sound. • Check to see if the A/V Receiver power is turned on. After the power is turned on, redisplay the Device Selection menu and press ENTER to allow NetCommand to correctly select the A/V Receiver input. • From the Setup Menu, select Review setting. Check the Review screen to see if the A/V Receiver inputs and device correspond to the actual conn...

Baixe o seu

Para fazer o download, introduza 2 dígitos :