Assessments - 2, GPA: 4 ( )

Fabricante : Mitsubishi Electronics Arquivo Tamanho: 10.02 mb Arquivo Nome : Língua de Ensino:

If you enter a code from the AUDIO chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V receiver with the TV all the time. In all other cases, only one of the below devices is allowed for each slide switch position. TV DVD/LDP Player Codes DVD/LDP brand Code to enter: Mitsubishi (DVD) 003 Mitsubishi (LDP) 016, 017 Panasonic 250 Pioneer DVD (LDP) 252 (016, 017) Sony 254 Toshiba 253 To reset to default code, enter GGG POWER О If your DVD code is not listed here, please see page 62 for a complete listing. Figure 4. LDP. Programming the remote to control your DVD/ Vposition: □ tv Q A/V receiver (volume and mute only) Cable/DBS position: Q Cable box Q Satellite receiver VCR CABLE/DBS DVD TV -, I I I AUDIO A/V Receiver Codes POWER О Audio brand Code to enter: Mitsubishi A/V receiver and/or CD player Set M-VR1000 or M-VR800 to 015 Set M-VR900 or M-VR700 to 010 Denon 234, 235, 236 Kenwood 200, 208 JVC 232, 233 Onkyo 209, 214 Pioneer 205, 207 Sony 222 Yamaha 201, 208 To reset to default code, enter GGG If your audio code is not listed here, please see page 62 for a complete listing. Figure 5. Programming the remote to control your A/V receiver. VCR position: Q VCR DVD position: Q DVD Q LD Player Audio position: Q A/V receiver Q Mitsubishi CD player [If you have a Mitsubishi A/V receiver, the audio position may be used in conjunction with select Mitsubishi CD players. Your audio position must be programmed to either 010 or 011. Plug the CD player power cord into a switched outlet on the back of your A/V receiver. Pressing the POWER button will then turn on your A/V receiver, in turn, turning on your CD player. On select CD players, the transport controls (FF, Play, Rew, etc.) in the audio position will operate the CD player.] I IMPORTANT 11 IMPORTANT I 3 -► If the slide switch is set to TV when you enter an A/V receiver code, VOLUME and MUTE will control the A/V receiver rather than the TV. To return volume and mute control to the TV, set the slide switch to TV, press and hold POWER and enter 000. Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, your remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver. 25 Programming the Remote Control: To Control Other A/V Products Activate the System 4 Home Theater IR Control Part III: Setup Programming the Remote Control: To Activate the System 4 Home Theater IR Control Models VS-60719 and VS-70709 Activation of the System 4 Home Theater IR Control You can, with certian digital A/V receivers, set up the remote control to automatically select the correct audio input when you press the HOME THEATER button. At the same time, the TV will select the correct video input. This allows you to watch your best type of video (Component, S-Video) with your best type of audio (Dolby Digital, Pro Logic, etc.) conveniently. See System 4 Home Theater IR Control, page 20, for connection instructions. Once properly activated, when the HOME THEATER button is pressed, System 4 Operates in 2 parts: audiO Changes a compatible digital A/V receiver to the correct input for the device you wish to operate. video| Changes the TV to the correct input for the device you wish to operate. To Activate the Audio Portion: j Press and hold the HOME THEATER button. ^ Press and release the AUDIO button. To Activate the Video Portion: (Figure 1) j Press and hold the HOME THEATER button. ^ Press and release the VIDEO button. Name the TV input as instructed. HOME THEATER VIDEO 3 Name TV Input as Shown Below (see pg 36 for naming help) Device You Are Using Name Input Cable Box connected to ANT-A or ANT-B Cannot be named Cable Box connected to Inputs 1 -3 CABLE Satellite Receiver connected to any input DBS VCR connected to Inputs 1-3 VCR DVD connected to Inputs 1-3 DVD Figure 1. Activating the video portion of System 4. Both functions can operate simultaneously with one touch of the HOME THEATER button. However, you may activate only one if you desire (video to control the TV or audio to control the A/V Receiver). The remote control must be programmed to the appropriate A/V Receiver code prior to the activation of the audio portion (see To Program the Remote to Control Other Brands of Audio and Video Products, page 24). 26 Part III: Setup Programming the Remote Control: To Activate the System 4 Home Theater IR Control Models VS-60719 and VS-70709 Testing System 4 for Proper Setup j Move the slide switch to the position you wish to test. ^ Point the remote at the TV. ^ Press and release the HOME THEATER button. If the audio portion has been properly setup, your A/V receiver will have changed to the appropriate input as indicated in table 1, page 15. If the video connection of your System 4 has been properly setup, your TV wil...

Baixe o seu

Para fazer o download, introduza 2 dígitos :