Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
Most wire has some indication (such as color code, ribbing, or writing) on one of the two conductors to help maintain consistency. If your speakers sound “thin” with little bass and little to no center image, the chances are that one of the speaker wires is connected backwards. Double check all connections. This system features a powered subwoofer (packaged separately) that has a built-in, adjustable low pass filter to separate the bass from the full range signal. The “subwoofer output” jacks (sometimes labeled “LFE”) on most receivers also contain a fixed low pass filter. If you connect the subwoofer to the receiver’s subwoofer output jack the two filters will interact and reduce the fidelity of your system. If you follow the hook up and the “receiver set up” instructions below, you will get all of the bass to the subwoofer and get the highest possible performance from your system. DO NOT USE THE “SUBWOOFER OUTPUT” (LFE) JACK ON YOUR RECEIVER TO CONNECT THE SUBWOOFER. BEST HOOK UP METHOD (Figure G) • Connect the left and right front speaker outputs of your receiver or amplifier to the SPEAKER LEVEL INPUTS of the powered subwoofer. • Connect the satellite speakers to the SPEAKER LEVEL OUTPUTS of the subwoofer. • If it is more convenient, parallel wire the subwoofer and satellites from your receiver. (Figure H) • Connect the center channel speaker directly to the center speaker output of your receiver or amplifier. • Connect the surround satellites directly to the rear or surround channel outputs of your receiver or amplifier. RECEIVER SET UP All surround sound receivers allow you to match the electronics to your speakers. Refer to the owners manual of your receiver or surround processor to learn how this is done. To get the best performance from the RM6600, use the following settings: • Front Speakers - Set to “Large” • Center Speaker - Set to “Normal” or “Small” • Surround Speakers - Set to “Small” • Subwoofer - Set to “Off” or “None.” This setting may not make sense to you as your RM6600 system has a subwoofer, but really, this is the right setting. ADJUSTING THE POWERED SUBWOOFER FOR BEST PERFORMANCE (RM6600 System) • Start with the VOLUME level at about 1:00. Adjust up or down until you get sufficient bass for your personal taste. Remember that room position can have a very large affect on perceived bass level. • Switch PHASE control to 180° (down position.) • Turn the LOW PASS to the middle of the shaded area for best blending between the subwoofer and the satellites. You’ll know the setting is correct when a high quality recorded male voice sounds full without any chestiness. If vocals sound thin turn this control up—if they sound boomy turn it down. (See Figures I & J) SAFE LIMITS OF OPERATION Your Polk loudspeakers are made with the highest quality materials for years of trouble-free performance. However, damage to loudspeakers can occur when an amplifier, regardless of its wattage, is made to play at higher listening levels than its power can clearly produce (usually beyond the “1 to 2 O’clock” position on the volume control). This results in very high levels of audible distortion, originating in the amplifier, which adds a harsh, gritty sound to the music. Contrary to popular belief, a speaker is more likely to be damaged by trying to get too much volume from a low-powered amp or receiver than from a high-powered one. MAINTAINING THE APPEARANCE OF RM SERIES SPEAKERS Your new speaker cabinet is made of a rugged material that can be dusted or cleaned with a moist cloth. Avoid harsh detergents and cleaning fluids; they can permanently damage your speakers’ finish. Gently vacuum the grilles to remove dust. TECHNICAL ASSISTANCE OR SERVICE If, after following the hook-up directions, you experience difficulty, please double check all wire connections. Should you isolate the problem to the speaker, contact the authorized Polk Audio dealer where you made your purchase or call Polk Audio’s Customer Service Department at 1-800-377-7655 (calls from US or Canada only) from 9am to 5pm, Eastern Time, Monday through Friday. You may also contact us via email polkcs@polkaudio.com. ENGLISH COMIENZO La caja de 5 unidades RM6600 debe contener las siguientes piezas: • Cuatro (4) altavoces satelite con blindaje magnetico • Un (1) altavoz de canal central con blindaje magnetico • Cuatro (4) soportes de montaje en la pared para los satelites frontales y con sonido envolvente y cuatro tornillos para instalarlos en el altavoz • Este manual y otros materiales impresos La caja del modelo RM2300 debe contener las siguientes piezas: • Dos (2) altavoces satelite con blindaje magnetico • Dos (2) soportes de montaje en la pared y cuatro (4) tornillos para instalarlos • Este manual y otros materiales impresos La caja del RM2600 debe contener las siguientes piezas: • Un (1) altavoz de canal central con blindaje magnetico • Este manual y otros materiales impresos COLOCACION DE LOS ALTAVOCES ALTAVOZ DE CANAL CENTRAL (Figuras A y B) Co...
Este manual também é adequado para os modelos :TV - RM2300 (273.97 kb)