Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
This unit is compatible with 1080i, 720p and 480p formats. Select the output of the connected device to match that of the unit. Connection diagram Follow the diagram below to connect the unit to a set top box or a DVD player. When audio signal input is digital. Set top box HDMIOUTThe connector on the unit is HDMI Type A connector. When audio signal input is analog. Set top box HDMI OUT AUDIO OUT The connector on the unit is HDMI Type A connector. Notes: 1 HDMI/HDCP = High Definition Multimedia Interface / High-Bandwidth Digital Copy Protection. 2 EIA/CEA-861/861B Profiles compliance covers profiles for transmission of uncompressed digital video including high bandwidth digital content protection. For assistance, please call : 1 888 VIEW PTV(843 9788) or, contact us via the web at: Installation Procedure 1 Connect the HDMI output from the set top box or a DVD player to the HDMI input on the back of the unit. • If you cannot display the picture because your Digital Set Top Box does not have a Digital Out terminal setting, use the Component Video Input (or the S-Video Input or Video Input). In this case, the picture will be displayed as an analog signal. 2 Press TV/VIDEO on the Remote Control to select HDMI input. By inputting a High-bandwidth Digital Content Protection high-definition picture source to the HDMI IN terminal of this Device Display, high-definition pictures can be displayed on the screen in their digital form. (This terminal is for use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.) Notes: • Select the HDMI input position by pressing the TV/VIDEO button. (P. 37) • The HDMI IN terminal can only be used with 1080i, 720p and 480p picture signals. • If there is no audio, check if the source equipment has PCM output. If not, please use analog connections. • Be sure HDMI is securely connected. If not, picture noise and/or incorrect picture display may result. • With HDMI connection, depending on the signal, the picture may be displayed with unnatural colors (as if red and blue are reversed). See UV Timing of Page 53. Compatible formats Video Signal: The Device display is compatible with following formats. Please set the connecting device to following format. Display mode No. of dots 1080i 1920 x 1080i 720p 1280 x 720p 480p 720 x 480p 640 x 480p Vertical scanning frequency (Hz) 59.94 / 60 59.94 / 60 59.94 / 60 59.94 / 60 Audio signal (PCM) When digital audio is included in the HDMI connection, the compatible sampling frequencies are 48 kHz/44.1 kHz/32 kHz. (See page 55) Getting ed Power ON / OFF Turning the Power ON and OFF Always be sure to follow the procedure given below to turn the Device Display power ON and OFF. • The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the POWER indicator will blink Red. Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary) while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the power indicator blinks Red. POWER button/ POWER indicator POWERSAPLIGHTTV/VIDEOA-ANTENNA-BVCRDVDDBSRCVRCBLAUX Power ON Press POWER on Device Display or Remote Control to turn power on. The Power Indicator blinks Green for about 10 seconds and then turns solid Green. Power OFF Press POWER on Device Display or Remote Control to turn power off. Power shuts off after a Black Screen is displayed for a few seconds. Note: If the POWER button is pressed during the Black Screen display, Power is turned back on. The Power Indicator blinks Red for about 1 minute and then turns solid Red. Note: When the AC Cord is unplugged, the internal cooling fan stops op er at ing. In this case, the lamp will be insufficiently cooled and will take a while to turn ON again. The Power Indicator LED ACTION Red Power – OFF (Standby mode) Red blink Power – OFF (Now cooling) Green Power – ON Green blink Power – ON (Preparing to light lamp) Notes: • If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the lamp automatically comes on. • After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal. • This unit consumes approx. 20 W in OFF condition when plugged into an AC outlet. For assistance, please call : 1 888 VIEW PTV(843 9788) or, contact us via the web at: Power ON / OFF First Time Setup For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures displayed on-screen for setting up the features. Input Setup To select the configuration of RF input depending on the signal source. Procedure Press VOL > to select Cable only, Cable/Antenna, or Antenna only. Press OK to underline your selection. When the next scre...
Este manual também é adequado para os modelos :TV - PT43LCX64 (3.02 mb)
TV - PT60LCX64 (3.02 mb)
TV - PT 50LCX64 (3.02 mb)
TV - PT 43LCX64 (3.02 mb)