Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Primary DNS 0 . 0 . 0 . 0 select ok or Select “LAN speed setting” (Default is “Automatic”) Normally, select “Automatic”. If “Connection test” failed, set the “LAN speed setting” to “manual” and then select “10BASE half duplex”, “10BASE duplex”, “100BASE half duplex” or “100 BASE duplex”. Cannot be selected when the “LAN speed setting” is “Automatic”. Changing the settings may make it impossible to connect some types of equipment. Network setting 2/2 MAC address 12-34-56-78-80-ab LAN speed setting Automatic LAN speed 10BASE half duplex Software update select adjust Select “Software update” Press OK to start the software update screen. Follow directions of the screen. * Set “Clock” first. (p. 18) Network setting 2/2 MAC address 12-34-56-78-80-ab LAN speed setting Automatic LAN speed 10BASE half duplex Software update select ok AdvancedNetwork Check that the network settings are as shown below, and then start “Connection test”. Select “Connection test” and press OK. Succeeded: “Connection test” succeeded Only home network: Home network is available. Failed: Check the broadband environment connection and settings and the network settings, and then perform the test again. Test in progress ---: Test not yet performed *Press OK again to cancel the test. (It takes a while to cancel the test.) Network setting 1/2 Connection test Succeeded IP setting mode Manual IP address 192.168.0.5 Subnet mask 255.255.255.0 Default gateway 192.168.0.254 select ok Select “IP setting mode” and set to “Automatic”. ¦Manual setting Select “IP setting mode” and set to “Manual” Select the item and press OK Check the specifications of the broadband router and enter each IP address. (When IP automatic acquisition in DHCP can be used) Network setting 1/2 Connection test Succeeded IP setting mode Automatic IP address 192.168.0.5 Subnet mask 255.255.255.0 Default gateway 192.168.0.254 The acquired address is displayed. select ok Subnet mask 0 . 0 . 0 . 0 changechannel ok orEach IP address is acquired automatically. Select “DNS setting mode” and set to “Automatic”. (When DNS automatic acquisition in DHCP can be used) Network setting 1/2 Connection test Succeeded DNS setting mode Primary DNS 192.168.0.20 Automatic Secondary DNS 192.168.0.21 The acquired address is displayed. select ok Each IP address is acquired automatically. If you are using a broadband router, IP automatic acquisition in DHCP can be used under normal circumstances. If you are not sure, check with the person who installed the equipment, or check the instructions for each device. ¦Manual settingSelect “DNS setting mode” and set to “Manual” Select the item and press OK Enter each IP address as was specified by the provider. Primary DNS 0 . 0 . 0 . 0 select ok or Select “LAN speed setting” (Default is “Automatic”) Normally, select “Automatic”. If “Connection test” failed, set the “LAN speed setting” to “manual” and then select “10BASE half duplex”, “10BASE duplex”, “100BASE half duplex” or “100 BASE duplex”. Cannot be selected when the “LAN speed setting” is “Automatic”. Changing the settings may make it impossible to connect some types of equipment. Network setting 2/2 MAC address 12-34-56-78-80-ab LAN speed setting Automatic LAN speed 10BASE half duplex Software update select adjust Select “Software update” Press OK to start the software update screen. Follow directions of the screen. * Set “Clock” first. (p. 18) Network setting 2/2 MAC address 12-34-56-78-80-ab LAN speed setting Automatic LAN speed 10BASE half duplex Software update select ok The network settings become effective when you close the menu and run “Connection test”. VIERA CASTTM Setting Display menu Select “Setup” Menu Picture Audio Timer Lock VIERA Link SD card Closed caption Setup select set or next Select “VIERA CAST setting” Setup 2/2 Advanced setup About Reset to defaults VIERA Link settings Network setting VIERA CAST setting Network Cameras list ECO/energy saving select ¦Press to exit from a menu screen Select the item and adjust select ¦Press to return to the previous screen VIERA CAST setting Proxy address Proxy port 0 Connection test Connection test Proxysetting • Proxyaddress • Proxy port Enteringcharacters Advanced VIERA CASTTM Setting Select “Connection test” and Press OK VIERA CAST setting Proxy address Proxy port 0 Connection test select ok When a connection is made to the connection test site and a message is displayed that indicates a successful connection The settings are correct. When the connection is not successful An error message is displayed on the screen. * Check the connection and settings. (p. 44-45, below) If you perform the proxy settings, check the proxy address and the proxy port number. Set only if specified by the provider. It is not required for normal household use. ¦Proxy address This is the address of the relay server that is connected to the target server instead of the browser and sends data to the browser. Setting is only required if specified by the provider. Select “Proxy...
Este manual também é adequado para os modelos :TV - TCP54V10 (3.34 mb)