Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Push until the hook clicks. 2. Pull off. 1. Keep the knob pressed. Unplug the AC cord Unplug the AC cord pressing the two knobs. Close Open 1 Plug the AC cord into the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper which is attached to the unit. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst. Note: One fi xing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Connections PC Input Terminals connection AUDIO PC IN COMPUTER Conversion adapter (if necessary) Mini D-sub 15pRGB PC cable Stereo plugAudio Connect a cable which matches the audio output terminal on the computer. (Male) (Female) Notes: • Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display resolution is a maximum of 768 . 720 dots (TH-37PR11UK/H), 768 . 768 dots (TH-42PR11UK/H) when the aspect mode is set to “4:3”, and 1,024 . 720 dots (TH-37PR11UK/H), 1,024 . 768 dots (TH-42PR11UK/H) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with suffi cient clarity. • The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. • Some PC models cannot be connected to the set. • There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. • The computer shown in the illustration is for example purposes only. • Additional equipment and cables shown are not supplied with this set. • Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. • Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. • Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 30) Signal Names for Mini D-sub 15P Connector 1 678 3 9 45 10 15 14 13 12 11 2 Pin Layout for PC Input Terminal Pin No. 1 2 3 4 Signal Name R (PR/CR) G (Y) B (PB/CB) NC (not connected) Pin No. 6 7 8 9 Signal Name GND (Ground) GND (Ground) GND (Ground) +5 V DC Pin No. 11 12 13 14 Signal Name NC (not connected) SDA HD/SYNC VD 5 GND (Ground) 10 GND (Ground) 15 SCL Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. (Male) 6 7 8 9 1 3 4 52 Pin layout for SERIAL Terminal SERIAL COMPUTER RS-232C Straight cable D-sub 9p (Female) Notes: • Use the RS-232C straight cable to connect the computer to the Plasma Display. • The computer shown is for example purposes only. • Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfi es the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level RS-232C compliant Synchronization method Asynchronous Baud rate 9600 bps Parity None Character length 8 bits Stop bit 1 bit Flow control - Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX : ETX C1 C2 C3 P1 P2 P3 P4 P5 Colon Parameter(s) End Start 3-character (1 - 5 bytes) (03h) (02h) command (3 bytes) Notes: • If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. • If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer. • SL1A, SL1B, SL2A and SL2B of Command IMS are available only when a dual input terminal board is attached. Signal names for D-sub 9P connector Pin No. Details 2 R X D 3 T X D 5 GND 4 • 6 Non use 7 8 (Shorted in this set) 1 • 9 NC These signal names are those of computer specifications. Command Command Parameter PON None POF None AVL ** AMT 0 1 IMS None SL1 SL2 SL3 PC1 SL1A SL1B SL2A SL2B DAM None ZOOM FULL JUST NORM SELF SJST SNOM SFUL Control details Power ON Power OFF Volume 00 - 63 Audio MUTE OFF Audio MUTE ON Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Slot1 input (INPUT1A) Slot1 input (INPUT1B) Slot2 input (INPUT2A) Slot2 input (INPUT2B) Screen mode select (tog...
Este manual também é adequado para os modelos :TV - TH-37PR11UK (3.76 mb)
TV - TH-37PR11UH (3.76 mb)
TV - TH-42PR11UH (3.76 mb)