Log:
Assessments - , GPA: ( )

Instruções de Operação Panasonic, Modelo TH-50PF50U

Fabricante : Panasonic
Arquivo Tamanho: 960.66 kb
Arquivo Nome :

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere


por este dispositivo também tem outras instruções :
TV - TH-50PF50U (929.37 kb)es

Facilidade de uso


AC cord connection (see page 13) Speakers (Optional accessories) AC cord fi xing Unplug the AC cord Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst. Using the clamper Secure any excess cables with clamper as required. Note: One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately. AC cord connection and fi xing, cable fi xing Speaker connection 1 Attach the clamper To remove from the unit: 2 Keep pushing both side snaps hole Bundle the cables snaps hooks Set the tip in the hooks To loosen: Keep pushing the knob knob Insert the clamper in a hole. Red Black While pressing the lever, insert the core wire. Red Black Return the lever. 11 Connections Video equipment connection SLOT: Terminal board (optional accessories) insert slot (see page 5) Note: The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. AV IN (HDMI): HDMI Input Terminal Connect to video equipment such as VCR or DVD player. WIRELESS MODULE, LAN: Refer to “Operating Instructions, Network Operations”. DVI-D IN: DVI-D Input Terminal PC IN: PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. SERIAL: Control the Plasma Display by connecting to PC. 3D IR TRANSMITTER: Connect the 3D IR TRANSMITTER (optional accessory). Terminals are on the bottom side of the Plasma Display. AV IN (VIDEO): Composite Video Input Terminal COMPONENT/RGB IN: Component/RGB Video Input Terminal 12 Example of Network Connection (Wired LAN) Connections To use the wireless function, the wireless module (ET-WM200U) (sold separately) is necessary. When connecting the wireless module to the display, remove the protective fi lm and cap. Connecting procedure Hold the wireless module with its LED on the near side and connect it to the wireless module connection terminal. Note: Do not connect any other device than the wireless module (ET-WM200U). Display (main unit, rear) Hub or broadband router LAN cable (not supplied) COMPUTER Less than 3.9 inch (10 cm) Less than 3.9 inch (10 cm) Ferrite core (supplied) Ferrite core (supplied) Installing the Ferrite core Pull back the tabs (in two places) Wind the cable twice Open Press the cable through and close Notes: • Make sure the broadband router or hub supports 10BASE-T/100BASE-TX. • To connect a device using 100BASE-TX, use “category 5” LAN cable. • Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge. Do not touch the LAN terminal or a metal part of the LAN cable. • For instructions on how to connect, consult your network administrator. ET-WM200 LED Connecting Wireless Module (Wireless LAN) INPUT MENU -/ VOL +/ ENTER/ 13 Power Indicator Remote Control Sensor Power ON / OFF Connecting the AC cord plug to the Plasma Display. Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst. Press the Power switch on the Plasma Display to turn the set on: Power-On. Power Indicator: Green [Starting up the network] It takes some time for the network to start up just after the power is turned on. During that time, “NETWORK SETUP” in the “SETUP” menu is grayed out and cannot be set. Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. Power ON / OFF English (UK) Deutsch Francais Italiano Espanol ENGLISH (US) РусскийOSD LANGUAGE SETSELECT DAY/TIME SETUP TIME MON 99:99 SET TIME 99:99 DAY MON When 3D images will be viewed by unspecified number of people or used for commercial applications, someone in authority should convey the following precautions. These precautions should be followed in the home as well. To enjoy 3D images safely and comfortably, please refer to the Operating Instructions for in-depth description. Please refrain from viewing 3D images if you do not feel well or are experiencing visual fatigue. When first switching on the unit Following screen will be displayed when the unit is turned on for the fi rst time. Select the items with the remote control. Unit buttons are invalid. OSD LANGUAGE DAY/TIME SETUP VIEWING ENVIRONMENT Notes: • Once the items are set, the screens won't be displayed when switching on the unit next time. • After the setting, the items can be changed in the following menus. OSD LANGUAGE DAY/TIME SETUP DISPLAY ORIENTATION PUBLIC SPACE: Suitable for commercial applications. HOME: Suitable for hom...

Este manual também é adequado para os modelos :
TV - TH-42PF50U (960.66 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias