Assessments - 3, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
-Do not install near or around any heating apparatus. . Use only recommended parts and components. (depending on your model) 10 ENG Installing the Display on the Wall Attachment Panel Wall Mount Bracket Mounting Kits (Sold Separately) 4 EA 4 EA Plastic Hanger Screws How to Adjust Mounting Angle 1 Secure the PDP to the wall mount bracket. (Please refer to the following instructions.) 2 Set the angle by pulling the upper end of the PDP attached to bracket in the direction of the arrow. 3 The angle can be adjusted from 0° to 15° by ±2°. The wall mount bracket is delivered separately. Please tighten the captive screw in the direction of the arrow after assembling the bracket. Installation Notes . Do not install the PDP on any place other than vertical walls. . To protect the performance of the PDP and prevent troubles, avoid the followings: -Do not install next to smoke and fire detectors. -Do not install in an area subjected to vibration or high voltage. -Do not install near or around any heating apparatus. . Use only recommended parts and components. (depending on your model) 11 ENG Installing the Display on the Wall Attachment Panel (continued) 1 Remove the screws from the back of the PDP. 3 Tighten the screws of the plastic hanger to the back side of the PDP. 4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket. 2 Use the screws and assemble the plastic hanger. . . Please ask the installers to install the wall mount bracket. . Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket. . Please avoid catching your fingers while installing and adjusting the angle. . Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP. Connecting External Devices to the PDP 1 Be sure to remove the safety pins underneath the PDP. . If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP. 2 Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks. . Using the PDP After Connecting External Devices. Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0o. . For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury. . The exterior of the PDP may be different than the picture. (Assembly and installation of the plastic hanger is the same.) . To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions: PDP panel Wall attachment panel bracket Wall 12 Connecting Speakers ENG 1 Remove the screws on the rear of the PDP. 2 Hang the two “T” shaped hangers on the square holes on the rear of the PDP. 3 Tighten the PDP and the speaker bracket using the screws removed from the PDP. . When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of personal damage and injury. 13 Connecting Speakers (continued) ENG Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. . . The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8.). . When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it. . Before connecting the speaker wire to the PDP, turn off your PDP. Ferrite Cores The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector. ENG ENG Connecting to an Aerial or Cable Television Network Rear of the PDP Cable Television Network or To view television channels correctly, a signal must be received by the set from one of the following sources: . An outdoor aerial . A cable television network . A satellite network 1 In the first three cases, connect the aerial or network input cable to the 75. coaxial socket on the rear of the PDP. 2 If you are using an indoor aerial, you may need to turn it when tuning your PDP until you obtain a picture that is both sharp and clear. For further details, refer to: . “Storing Channels Automatically” on page 19 . “Storing Channels Manually” on page 20 . When installing or re-installing your PDP, be sure to use the supplied coaxial antenna cable. If you connect using a different coaxial cable, there is risk of noise or interference to the screen image. (You must not use another general purpose cable.) Connecting a Satellite Receiver or Decoder 14 Rea...