Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Mode Description optimum adjustment automatically. Horizontal Moves the picture left/right. Position The adjustment range is within ±50 from center.* Vertical Moves the picture up/down. Position The adjustment range is within ±10 from center.* Clock Phase Helps to reduce noise and sharpen the picture. The adjustment range is within ±16 from center.* Sampling Clock Helps to reduce noise and minimize periodic vertical stripes on the screen. The adjustment range is within ±10 from center.* Auto Adjust Highlight this item then press to get an * The default settings may vary depending on the input signal format. Setting the PC Audio This function allows you to output or mute the sound from your PC when connecting using the PC IN terminal and an analog RGB cable. (. page 19) To set the PC Audio: 1.. .. .. Press and open the Audio menu. Highlight Audio Setup and press . Press • or • to select PC Audio and then press • or • to select No or Yes. Yes: When viewing the PC input, the audio from the PC Audio input can be heard. No: When viewing the PC input, there will be no audio. Note: Because the PC and HDMI-1 inputs share the same set of analog audio inputs, the PC Audio menu setting influences the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to “Yes,” the HDMI 1 Audio setting is set to “Digital” and is grayed out in the menu. (Also see item 3 on page 11 and “Setting the HDMI™ Audio mode” on page 32.) Setting the sleep timer You can set the sleep timer to turn off the TV after a set length of time (maximum of 180 minutes). To set the sleep timer using the remote control: Press on the remote control to set the length of time until the TV turns off. Repeatedly press to increase the time in 10-minute increments, or press • or • to increase or decrease the time in 10-minute increments, to a maximum of 180 minutes. To set the sleep timer using the on-screen menus: 1.. Press and open the Setup menu. .. Highlight Sleep Timer and press . .. Press the Number buttons to enter the length of time in 10-minute increments. .. Highlight Done and press . Note: When a power failure occurs, the sleep timer setting may be cleared. To display the remaining sleep time: Press . Note: A message will display on-screen when there is one minute remaining on the sleep timer. To cancel the sleep timer: Repeatedly press until it is set to 0 minute. 9 Chapter 6: Using the TV’s features Displaying TV status information To display TV status information using RECALL: Press on the remote control. The following information will display (if applicable): • Current input (ANT/CABLE, VIDEO, etc.) • If ANT/CABLE is the current input, either “CABLE” (for cable TV) or “ANT” (for over-the-air broadcasts). • Channel number (if in ANT/CABLE mode) • Channel label (if set) • Digital signal strength indicator (bar graph in lower right corner of box; for ATSC signal only) • Stereo, Mono or SAP audio status (when HDMI input mode, Dolby Digital or PCM) • Video resolution • Aspect ratio of incoming video signal (4:3 or 16:9) • V-Chip rating status • Game Timer (if set) To close the RECALL screen: Press again. To display TV status information using INFO: Press on the remote control. The following additional information will display for off air digital channels (if applicable): • Title • Duration • Detailed description Understanding the auto power off feature The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This feature functions in ANT/CABLE mode only. Understanding the last mode memory feature If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns on the TV when the power is resupplied. Note: If it’s possible, and you will be away from the TV for an extended period of time you should unplug the power cord. Note: The location of the banner can be moved to the top or bottom of the screen by pressing p or q while the RECALL or INFO display is on-screen. (The last position will be stored to memory.) 0 Chapter 7: Using the TV’s advanced features Using the advanced picture settings features Using dynamic contrast When dynamic contrast is set to On, the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video. To select dynamic contrast preferences: 1.. Press and open the Video menu. .. Highlight Picture Settings and press . .. HighlightAdvanced Picture Settings andpressIntheDynamic Contrast field,selecteitherOff orOn. . .. . To save the new settings, highlight Done and press . To revert to the factory defaults, highlight Reset and press . Note: If you select one of the factory-set picture modes (Sports, Standard, Movie, or PC) and then change the dynamic contrast setting, the picture mode automatically changes to Preference. Using the static gamma feature The st...
Este manual também é adequado para os modelos :TV - 22AV500U (8.47 mb)