Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
TV - 22PFL3505D/F7 (1.06 mb)
TV - 22PFL3505D/F7 (10.32 mb)
TV - 22PFL3505D/F7 (1.12 mb)
Facilidade de uso
3 Press MENU to exit. PictureSound Setup Features Language Antenna Cable Back Autoprogram will rescan all channels. Auto programming may take more than 20 minutes to complete. Select your signal source. Antenna Cable Or Picture ANT.IN • When autoprogramming is complete, the lowest memorized channel will be displayed. 4 Follow the on-screen instructions to complete the installation. 22 EN Channel list Add channels English The channels selected here can be skipped when selecting the channels using CH + / .. Those channels can still be selected with the Number buttons. 1 Press MENU on the remote control and select [Setup] > [Channel List]. Picture Sound Features Language Setup Picture Add Channels Antenna Autoprogram Channel List 2 Press I or i to select the channel you want to remove, then press OK. Ch Select Watch/Skip Back BACK OK Highlight channels for Ch Up/Down key selection. 40.2 40.3 DTV DTV Picture Sound Features Language Setup DTV 40.1 • The channel display for the removed channel darkens.You will not be able to select the channel again using CH + / .. • To reactivate a removed channel, press I or i and press OK. The registered channels are highlighted. • When you remove a major channel, its minor channels are removed as well. Note • The channel with the [DTV] indicated on the display is ATSC. Otherwise the channel is NTSC. 3 Press MENU to exit. This function lets you add the channels that were not added by the autoprogram due to the receptible condition at the initial setup. 1 Press MENU on the remote control and [Setup] > [Add Channels]. Channel List Antenna Autoprogram Picture Sound Features Language Setup Add Channels 2 Press a number (1 to 135) to enter the number of the channel you want to add, then press OK. 11 For analog channels, select a channel to be added using number keys. For digital channels, you must perform Autoprogram function. Add channels Ch Change Back BACK Picture Sound Features Language Setup 3 Press MENU to exit. Note • If setup completes successfully, [Added to the channel list] is displayed. • If external input is used, it is not possible to register the channel and [Unavailable] will be displayed on the TV screen. • By pressing I or i you can select the memorized channels only. • In most cases, digital channels are not broadcast on the RF channel on which they appear on your TV.To add digital channels you need to know the RF channel on which the digital channel is being broadcast. E.g. If there is a digital channel 9.1 which is being broadcast on RF channel 25, you need to enter 25 while performing a weak channel installation. To find out the RF channel on which a par ticular digital channel is being broadcast, please contact your local ser vice provider. Installing digital channels using [Add channels] might not work for direct cable connections and if the digital signal is too weak for the TV to process. Optimizing the signal quality from your antenna You can optimize your signal quality by tuning in ATSC channels with weak signals, and adjusting the antenna. 1 Press MENU on the remote control and select [Setup] > [Antenna]. 2 Press OK to confirm your choice. 3 Press a number (1 to 135) or press CH + or CH. to select the channel for which you want to check the digital signal strength. 4 Press MENU to exit. EN 23 24 EN Upgrading software 1 Prepare the software upgrade (see ‘Preparing for the software upgrade’ on page 24). 2 If the TV is on, press . POWER at the side of the TV. 3 Connect your USB device to the service terminal on the side of your TV. 4 Switch on the TV. » The TV scans the USB device for the upgraded software and automatically enters upgrade mode. 5 Read the on-screen instructions and confi rm that you want to continue with the installation. SSooffttwwaarree UUppggrraaddee Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Downloading... 60% 6 When the software upgrade is complete, remove the USB device. 7 Press . POWER at the side of the TV to make sure the unit goes to stand-by mode. 8 Switch on the TV. » The TV starts up with the new software. • The following messages are displayed without starting software upgrade when it doesn’t fulfi ll the upgrade conditions. SSooffttwwaarree UUppggrraaddee The version of this update file is the same or older than the current version. Please check the file and try again. 8 Upgrade your TV software Philips continuously tries to improve its products and we strongly recommend that you upgrade the TV software when upgrades are available. New software can be downloaded from our website at using the model number of your TV (e.g. 22PFL3505D) to fi nd information. Checking your current software version 1 Press MENU on the remote control and select [Features] > [Current Software Info]. » The version and a description of the current software is displayed, then press OK. Release Version: XXXXXXX_XXX_X_XXXX Picture Sound Setup La...