Assessments - , GPA:
(
)
)
Fabricante : Philips
Arquivo Tamanho: 12.96 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13 6. Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Code list of all brands / equipment Information to the consumer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 1. Introduction Congratulations on your purchase of the Philips SRM 5100 univ control. After installing the remote control y 4 different devices with it: Windows Vista™ TV, projector, HD TV), STB (Set Top Box, terrestrial receiver / decoder) and AMP (amplif System). You can find information about ho for use in the chapter ‘Installing the remote control’. 2. Installing the remote contr Connecting the receiver (for PC onl • Plug the receiver USB connector into one of the PC’s / laptop’s USB por ts. – A green LED lights up, indicating that the receiver is deriving its power from the PC / laptop. – A red LED lights up. The PC / laptop is no looking for the driver. As soon as the dr found the red LED goes out. The receiv now ready for use. Inserting the batteries in the r 1 Press the cover inwards and slide it in the direction of the arrow. 2 Place two AAA type batteries into the batter compar tment as shown. 3 Slide the cover back and click it firm place. Note: If, after ever y key press, all indicator LEDs (PC and then go out one after another, the remote control is indicating that its batteries are running low. Replace the batter 4 the remote control commands. • If the PC does not respond to key commands properly inserted and the USB connector is proper laptop USB port. See ‘Setting the remote control’. Other devices (TV, STB and AMP) The example below (TV - TV, LCD TV, plasma TV you how to do this. You can repeat the same steps f (STB and AMP) which you want to operate using the SRM 5100. Example of TV: 1 Turn your TV on manually or use the or Tune to channel 1. 2 Press the MODE key to select TV. Press the key until the TV LED lights up – The LED lights up for 10 seconds and then goes out. • If the LED does not light up, check whether the batteries are properly inserted. See ‘Setting the remote control’. 3 Check whether all keys are working. For an over view of the keys and their functions see ‘3. Keys and functions’. – If the TV responds as it should to all of the key commands the SRM 5100 is ready • If the device does not respond at all or not to all of the k commands, follow the instructions under control’, or for online setup go to: www Setting the remote control There is no need to set up the remote control f Vista™ based PC. For operating other devices set up is onl device (TV, STB and AMP) does not respond to the SRM 5100. If that is the case, the SRM 5100 does not recogniz model of your device and you need to progr The example below (TV - TV, LCD TV, plasma TV you how to do this. You can repeat the same steps f (STB and AMP) which you want to operate using the SRM 5100. The SRM 5100 emits the ‘switch TV to standb TV that are stored in the memor y. 2 Press the MODE key to select TV. Press the key until the TV LED lights up – The LED lights up for 10 seconds and then goes out. 3 Then keep keys 1 and 3 pressed simultaneously for three seconds until the LED flashes twice and then remains lit. 4 Press the SRM 5100 Standby (y) ke – The TV LED goes out and the SRM 5100 no star ts emitting all known ‘switch TV to standb signals, one by one. Each time a code is sent, the TV LED lights up 5 When your TV switches to standby, immediately press the SRM 5100 Standb key to stop the auto-search. – The TV LED blinks twice and then goes out. found a code that works on your TV 6 Check if you can operate all functions on y • If this is not the case, you can redo the automatic setting. The SRM 5100 will then search for a code that works better – After the SRM 5100 has run through all the kno will stop automatically and the TV LED will stop flashing. – Automatic programming of a TV tak For STB and AMP this time is 2 min 6 Manually setting the remote control Example of TV (TV, LCD TV, plasma TV, projector, HDTV): 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more fourfigure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, STB and AMP. On our website you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Press the MODE key to select TV. Press the key until the TV LED lights up. – The LED lights up for 10 seconds and then goes out. 4 Keep keys 1 and 3 pressed simultaneously for three seconds until the TV LED flashes twice and then remains lit. 5 Then enter the code noted in step 2 using the digit keys. – The TV LED key will now flash twice. If the LED flashes once for an extended period, the code has not been entered properly ...