Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Intended use of the input: digital set-top boxes and inputs from other digital video devices. NOTE: This DVI jack is not for computer connections. VGA cannot be connected. 7 1 2 3 4 6 DVI G S-VIDEO G S-VIDEO R L V R L R L R L V Pr Pb Y R L R L Pr Pb Y Pr Pb Y R L V STANDARD/ HD INPUTS STANDARD/ HD INPUTS TUNER RGB+HV AV5 AV6 AV1MONSUB OUT AV2AV3AV4 OUT SERVICE 12 C 5 8 9 10 Jack Panel Located on the Left Side of the TV Definitions: NTSC—National Television System Committee. CVBS—labeled “V,” provides a small step up in quality from the Tuner (RF) input. Called Composite Video. S-Video (Y/C)—provides better picture quality than CVBS. Separates the signal into color and brightness. YPbPr—provides the best quality video signal. Called Component Video Input, the signal is split into three parts, two color and one brightness. 10 10 SIDE JACK PANEL Signals accepted: NTSC (480i). Inputs available: S-Video (Y/C) and CVBS, plus audio left and right. Output available: Headphone. Only one of the inputs can be used at a time. Select the Side source, and the TV detects the input to which you have connected. Connections must be made to the audio inputs for sound. 8 Pre-connection Recommendations Positioning the TV Before connecting accessory devices—VCR, DVD player, or HD satellite receiver, for example— please keep the following in mind: • Place the TV on a flat surface. An unlevel surface may adversely affect picture performance. • Do not place the TV on shag carpet or any surface that will block the ventilation openings at the bottom of the set. Blockage will cause the TV to overheat and shut down. • Allow 4 to 6 inches of space behind the TV for ventilation. • An optional swivel and an optional stand are available for use with your TV. See your electronics dealer. • Test various locations in the room to find the optimal spot to locate the set for best viewing. • Do not place the TV in direct sunlight or near a heating appliance. • Do not expose the TV to rain or moisture. • To prevent any unsafe situations, do not place objects on top of the TV. Providing Protection Against Power Surges • Connect all accessory devices before you plug any of their power cords into the wall outlet or power strip. NEVER plug your TV into an outlet that is controlled by a wall switch. • Turn off the TV and/or accessory devices before you connect or disconnect any cables. • Ensure that all antennas and cables are properly grounded. See page 3, “Important Safety Instructions.” Protecting Accessory Devices from Overheating • Arrange accessory devices so that air can circulate freely around them. • Don’t stack the accessory devices. Arrange them to allow for good ventilation. The optional Philips stand provides enough room for two accessory devices, side by side. • If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it will not flow around other components. Connecting Cables Be sure to insert each cable firmly into the correct jack. Using the Connection Examples in This Manual The accessory device jack panels shown are for example purpose only. The jack panels on your accessory devices may look different. Also, note that connections can be made in various ways. The examples are presented only as guides. Situate the TV where it will not be exposed to heat or moisture. of the TV. a flat surface. Allow 4 to 6 inch- es behind the TV for ventilation. Place the TV on For safety, do not set objects on top Do not place the TV on a surface that will block the air filters located underneath the set. Optional Swivel Optional Stand POWER SELECT GUIDE INFO HIGH DEFINITION POWER OPEN/CLOSE STANDBY-ON STOP PREV NEXT PLAY PAUSE DVD619 DVD/CD PLAYER 9 Connecting a VCR Connecting a VCR 1 1 Connect the incoming antenna or cable TV signal to the ANT IN jack on the back of the VCR. 2 2 Using a coaxial cable, connect to the OUT jack on the back of the VCR and to the TUNER jack on the back of the TV. 3 3 Using A/V cables, connect from the AUDIO and VIDEO OUT jacks on the back of the VCR to the corresponding AV2 audio (L and R) and video (V) jacks on the back of the TV. 4 4 Press the AV+ button on the remote control to access the Source list. 5 5 Press the Cursor Up or Down button to select the AV2 input source. 6 6 Press the OK button to confirm your choice. The set is now switched to the AV2 input source for the viewing of programs from the VCR. NOTE: Since you’ve connected the cable TV signal directly to the TV’s tuner (step 2 above), you can watch the unscrambled programs by simply tuning to the desired channel. To store channels in the TV’s memory, you must use Autoprogram, which you can access through “Install” in the TV’s on-screen menu. See the Autoprogram section in the Quick Use and Setup Guide that came with the TV. If you use Autoprogram, you can select channels by pressing the CH + or – buttons on the TV remote control (in TV mode). Otherwise, you must press the digit (number) buttons to tune directly to the ...
Este manual também é adequado para os modelos :TV - 55PL9224/37B (2.09 mb)