|
Facilidade de uso
Note: The maximum number of channels including Aux sources that can be transferred to the TV controller is 140. 5. Add Custom Channel Labels for analog channels: 2-5-4 + Menu Mode Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to channel onscreen displays. Note: Digital Channels often have a broadcaster generated label. When done to exit mode, press MENU. 6. Verify TV Setup At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements. Set Installer menu item 028 Ch Overide to 000 to lock the channel scan. After the preceding has been completed, the Master TV setup is ready to be copied to a Clone Programmer, see Clone programmer pages. 000 INSTALLER SEQ 000 HOSPITAL PTC INSTALLER MENU Typical TV Installer Menu UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 003 BAND/AFC 00X 028 CH. OVERIDE 001 117 FACT DEFAULT 00X Review the settings for these Installer Menu Items DIGITAL 19-3 MONO STEREO SAP WXYZ Custom Channel Label ‘WXYZ’ created in 2-5-4 + Menu (Add Channel Label) Mode 028 CH. OVERIDE 000 After Master TV setup has been completed, set Installer menu item 028 Ch Overide to 000. PAGE 7 Typical Connections Panel HDMI/DVI IN AV IN 1COMPONENTIN USB IN SERVICE ONLY VIDEO AUDIO R-AUDIO-L (MONO) VIDEO RL RGB IN (PC) RS-232C IN SERVICE ONLY UPDATE RESET AUDIO IN (RGB / DVI) REMOTE CONTROL OUT SPEAKER OUT 8 CPBY PR ............... ..... .................... PILLOW SPEAKER PILLOW SPEAKER NORMAL SPEAKER SPEAKER SWITCHS-VIDEO AUDIO IN (RGB / DVI) Audio connection for RGB or DVI device. COMPONENT IN Connect to output jacks on component device. INPUT PORT here. SWITCH pillow speaker. USB IN Restricted to service use only. HDMI/DVI IN PORT Connect to output jacks from HDMI / DVI device. AUDIO/VIDEO IN 1 Connect to output jacks on audio/video or S-Video device. (8-OHM) RGB IN (PC) RS-232C IN TV software. UPDATE Software downloads and debug mode enable/disable. RESET Connection for RGB hookup from PC Hardware reset to PTC microcontroller. Provided for updating PILLOW SPEAKER Connect pillow speaker PILLOW SPEAKER Set to NORMAL SPEAKER to hear TV speakers sound. Set to PILLOW SPEAKER to hear pillow speaker sound and have TV controllable with SPEAKER OUT Connect to 8 ohm external speaker input. REMOTE CONTROL OUT IR output for controlling an auxiliary device. P A GE 8 206-4071 A/V Input 2: Side Connections Panel / RF Antenna Connection Headphone Output Port Connect headphone to this port. L/MONO-AUDIO-R IN Connect to audio output jacks from external device. For only mono audio output, connect to Left audio input. VIDEO IN Connect to video output port on external device. AV IN 2 L/ MONO-AUDIO-RVIDEO H/P RF Antenna Connection RF ANTENNA Connect to Antenna / Cable input on MPI card. Antenna or CATV ANTENNA /CABLE M.P. I. PAGE 9 MPI Card Slot The MPI card is equipped with an RF jack for antenna/cable signal source connection. The slot is also available for installing a PPV (Pay-Per-View) card. MPI Card Removal / PPV Card Installation 1. Remove the two MPI card retainer screws. 2. Pull out current MPI card far enough so that the RF cable can be detached from the old card. 2. Detach RF cable. 3. Place new PPV card into slot and slide it in far enough to reconnect RF cable. 4. Reconnect RF cable. 5. Insert card all the way into the slot making sure it is fully seated into back plane connector. 6. Replace the two card retainer screws. DC IN ANTENNA /CABLE M.P. I. M.P. I. Card Slot RF CABLE RF cable needs to be disconnected to remove current card. PAGE 10 206-4071 Vesa Standard TV Mounts General Guidelines: Choosing a Location for installing a VESA Standard Mount To the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV. Be sure the style of stand selected is capable of supporting the weight of the TV and is appropriate for the application. Wall Mounts If the mount will be on a wall, a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount. The wall mount location chosen should be appropriate for drilling holes and have available the required power source as well as antenna/ cable and any other equipment leads as necessary. Pedestal Mounts and Stands A sturdy surface on a desk or other similar flat table-like furniture would be the appropriate location for mounting a pedestal-style TV stand. Most stands are designed so that the wiring is threaded through the stand itself or a loop- through style clamp so that the wiring is neatly bunched and not strung in such a way as to create a potential hazard to the user. (Some stands are portable and can be moved from one location to another.) Be sure all safety considerations are followed. Typical Wall Stud Type Mount with SwivelBracket Typical Ped...
Este manual também é adequado para os modelos :TV - 32-3DCH-UA (323.09 kb)