Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Please retain this guide for your future reference. Please follow the steps to setup your TV: zzz For service and technical assistance, call our Customer Information Service Center (Toll Free): US residents: 1-800-222-SONY (7669) or visit Canadian residents: 1-877-899-SONY (7669) or visit DO NOT RETURN TO THE STORE 2 1 3 zzz Projection Lamp: Periodic replacement of the projection lamp will maintain the picture quality. See Replacement Lamp section of the manual. Wide Mode: Selecting appropriate screen mode will increase enjoyment of your TV viewing. When watching a Standard Definition source (4:3 aspect ratio) on this TV, you will see bars on both the left and right sides of the screen. Press the WIDE button on your remote to cycle through different screen modes to fill the screen in various ways. (Wide Zoom enlarges the center, Normal is how your TV receives the signal, Full stretches horizontally and Zoom enlarges the image proportionately to fill the screen.) When watching a High Definition source (16:9 aspect ratio) on this TV, you will see screen filled with a image. Press the WIDE button on your remote to toggle through different screen modes, especially zooming in to the center of the screen. (Wide Zoom enlarges the center, Full displays the image at its original size, Zoom enlarges the image proportionately to fill the screen.) When the TV receives a 720p or 1080i formatted signal, the Normal mode is not available. See Using WIDE Button section of the manual. If you feel the images on the screen is stretched, press the WIDE button to select a different screen mode. Running Initial Setup Notes on your new TV 1 Press to turn on the TV. The Initial Setup screen appears. 2 Press V or v to highlight the on-screen display language. Then press . The message “First please connect cable and/or antenna” appears. This may require 50+ minutes for completion and “Start auto program now?” appears. 3 Press (Yes) to start Initial Setup. Initial Setup automatically creates a list of receivable channels from both VHF/UHF antenna and cable TV channels if both sources are connected. When Initial Setup is complete, the TV will display the total number of analog channels and the total number of digital channels found. 4 Press to exit this screen. To run Auto Program again at a later time Refer to the manual on “Initial Setup” and “Auto Program” sections. 2 Best Audio/Video Performance Activating CableCARD™ Service Before you can use CableCARD service, you need to insert the CableCARD device (supplied by your cable provider) and activate the service. Inserting the CableCARD incorrectly may result in permanent damage to the card and the TV. The connection diagrams shown in the reverse side are recommendations only; other possible solutions may exist. Connections that include an AV receiver can often be complex, so check your AV receiver’s instruction manual for additional details. See the “Cables Required” chart that appears with the diagram to determine which cables you’ll need. Depending on the components you plan to connect, you may need to purchase extra cables. 1 Connecting Your TV Programming the Remote Control The remote control is preset to operate Sony brand video equipment. Sony Equipment Programmable Code Number DVR 772 DVD/VCR 601 (Sony Dream System) SAT/CABLE 801 (Sony Satellite Receiver) Follow the steps below to program your TV’s remote control to operate the non-Sony video equipment. Find the three-digit code for your equipment from the “Manufacturer’s Codes” listed on right. If more than one code number is listed, try entering from the code listed first. 1 Press and hold the , or FUNCTION button you want to program on the remote control and press the button simultaneously. The selected FUNCTION button ( , or ) will flash. 2 Enter the three-digit manufacturer’s code number using the 0-9 buttons while the button is lit. If code is not entered within 10 seconds, you must perform the step 1 again. 3 Press button. When programmed correctly, the selected FUNCTION button will flash twice, and when not, it flashes five times. To check if the code works Aim your TV’s remote control at the equipment, and press the green button. If the equipment responds, the programming is completed. If not, try the next code listed. 3 If no code is input within the above specified time, or an invalid or incorrect code number is input, the remote control automatically goes back to the previous setting. In some cases, you may not be able to program your remote control to operate other equipment. In such cases, use the equipment’s own remote control. Removing the batteries or dead batteries may cause the programmed codes to be lost and revert back to the factory setting. Reprogramming the codes may be necessary. 1 2 3 1 Manufacturer’s codes DVD Players Manufacturer Code Sony 751 General Electric 755 Hitachi 758 JVC 756 Magnavox 757 Mitsubishi 761 Panasonic 753 Philips 757 Pionee...
Este manual também é adequado para os modelos :TV - E50A10 (1.48 mb)