Assessments - , GPA:
(
)
)
Fabricante : Sanyo
Arquivo Tamanho: 1.5 mb
Arquivo Nome : ab0debcf-bfaa-7ed4-15d9-8e93b4a9894c.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
5. Follow on-screen instructions, see 2. Connect signal, see below. pages 10 ~ 12. 3. Plug in AC power cord. CONNECTING CABLE SERVICE, OR RF ANTENNA, OR SATELLITE DISH CATV FRANCHISE NOTE: Cable companies, like public utilities, are franchised by local government authorities. To receive cable programs, even with equipment which is capable of receiving cable channels, the consumer must subscribe to the cable company’s service. AUDIO VIDEO INPUT 2 R L UHF/VHF/CATV PR PB Y VIDEO (MONO) S-VIDEO COMPONENT 2 IN FROM ANT. OUT OUT TO TV CATV IN OUT TO TV S-VIDEO CH3 CH4 VIDEO L-AUDIO-RVIDEO L-AUDIO-R IN FROM SAT. IN OUT RECEIVER TO TV Cable Box RF AntennaSatellite Receiver TV Back VCR Back Operational Tip for No Signal Connection: If the TV is used as a monitor only, with a DVD player or some other type of external equipment, and no cable or antenna signal is available, the following setup is necessary: – Your TV is designed to automatically search for available channels. Therefore, the initial start up requires that you press the MENU key, enabling the TV to auto- matically go through the channel search process before you can operate the TV. After the initial channel search is com- pleted, you must press the MENU key again to complete the channel search process. This may take several minutes. – After the channel search process is com- plete (2 searches), you can press the INPUT key on the remote control to use the TV as a monitor. Notes: – If you do not have a cable box, connect cable directly to TV 75 ohm jack or VCR. – If you do not have a VCR, connect signal directly to TV 75 ohm jack. OR OR The TV will automatically select the correct Antenna Exception—When the Video mode is selected, the TV will mode for the type of RF signal you connect. not automatically switch off when signal reception has stopped for 15 minutes. TV will switch off automatically after 15 minutes if there is no signal reception (cable out or station not broad- If you move the TV to a new location, press the RESET casting). key twice after connecting the signal and turning on the TV. Need help?Visit our Web site at or Call 1-800-877-5032 FRONT FRONT AND REAR PANELS VIDEO IN L- AUDIO -R MENU CH VOL POWER Audio Video Input Jacks (AV1) Connect video equipment here (see page 7). BACK 480i Component Video In Jacks (Component 2: Y, Pb, Pr) Connect video equipment here (see page 6). Note: Audio Video Input 2 (AV2) and Component inputs share the same audio (R/L) input jacks. Audio Video Input 2 Jacks (AV2) Connect video equipment here (see pages 6 and 8). Note: S-Video connection will override an AV2 video connection. S-Video In Terminal To enhance video detail use the AV2 S-Video jack instead of the AV2 Video jack, if available on your external equipment. (An S-Video connection will override connection to the AV2 video input jack. See page 8.) POSITIONING THE TV Do not position the TV in a confined area. Allow space for normal air circulation around electronic parts. Need help?Visit our Web site at or Call 1-800-877-5032 USING THE COMPONENT VIDEO AND AUDIO INPUT JACKS CONNECTING A DVD PLAYER Switch off TV and external equipment before connecting cables. (Cables are not supplied.) Connect a DVD Player or other equipment’s interlaced Component Video Out to the TV Component Video In (Y-Pb-Pr) Jacks. Connect the DVD Player’s Audio Out to the TV AV2 Audio In (L/R) Jacks. Press POWER to turn on the TV. Turn on external equipment also. To access Audio Video inputs, press the INPUT key to select COMPONENT2. Notes: DVD Player component output must be set to Interlaced (480i). Audio Video Input 2 (AV2) and Component inputs share the same audio (R/L) input jacks. Connect equipment to the Component2 video input or the AV2 video input, but not both types at the same time. DVD Player Y PB/CB /CRPR COMPONENT VIDEO OUTAUDIO OUT RL DIGITAL OUT COAXIAL S-VIDEO OUT VIDEO OUT VIDEO OUT SELECT S-VIDEO COMPONENT AUDIO VIDEO INPUT 2 R L UHF/VHF/CATV 75. PR PB Y VIDEO COMPONENT 2 S-VIDEO TV BACK What you will need for connections: Component video cable – 1 Audio Cable – 1 123RESETINPUTPOWER123 Remote Control ¦ A solid Blue screen with COMPONENT2 displayed Press INPUT key after connecting cables to access means that the Video mode is selected, but no signal the AV inputs.There is NO need to tune to a blank is being detected at the Component jacks. Check channel. connection, and turn on external equipment. Need help?Visit our Web site at or Call 1-800-877-5032 USING THE FRONT VIDEO AND AUDIO INPUT JACKS CONNECTING A VIDEO GAME OR OTHER EQUIPMENT Switch off TV and external equipment before connecting Press POWER to turn on the TV. Turn on external cables. (Cables are not supplied.) equipment also. Connect game Audio Output (R/L) to the TV Audio To access Audio Video inputs, press the INPUT key to Input (R/L). Then connect game Video Output to the TV select GAME or select using the menu. Video Input. CH VOL PO...