Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
4 AUDIO Press to select the sound mode. Your can select STANDARD, NEWS, MUSIC, or MEMORY. You can set upyour own sound mode settings and save themunder the MEMORY mode. 5 CCD Press to turn closed captioning on or off. 6 CH , CH , VOL , VOL Press the channel buttons to change channels. Press the volume buttons to increase or decrease the volume. 7 MENU Press to open the on-screen display (OSD). 8 POWER Press to turn your TV on oroff. If your TV is in standby(power saving) mode, press to exit standby mode. 9 RECALL Press to go to the previous channel you were watching. 10 PICTURE Press to select the picture mode. You can select STANDARD, DYNAMIC, MILD, or MEMORY. You can set up your own audio modesettings and save themunder the MEMORY mode. 11 INPUT Press to select the video input source. Setting up your TV Installing remote control batteries To install remote control batteries: 1 Remove the battery cover. 2 Insert two AAA batteries into the battery compartment. Make sure that the + and – symbols on the battery match the + and – symbols inside the battery compartment. 3 Replace the battery cover. No. Button Description 1 MUTE Press to mute the sound. Press again to restore thesound. 4 Insignia NS-R20C Round Tube TV Connecting an outside antenna or cable TV To connect an antenna or cable TV: 1 Plug a 75-ohm cable into the antenna jack on the back of your TV. 2 Plug the other end of the cable into a cable TV or outside antenna source. Connecting a standard video device To connect a standard video device: 1 Plug a video cable into the VIDEO jack on the front of your TV, then plug the other end of the video cable into the VIDEO OUT jack on the video device. 2 Plug the left and right audio cables into the AUDIO L and AUDIO R jacks on the front of your TV, then plug the other ends into the left and right AUDIO OUT jacks on the device. Warning Do not throw batteries into fire. Dispose of used batteries as hazardous waste. Caution Do not drop or disassemble the remote control. Do not get the remote control wet. Caution When the remote control will not be used for a long period of time or when the batteries are word out, remove the batteries to prevent leakage. Note If you use a 300-ohm flat cable, you need to connect a 300-to-75-ohm converter to the flat cable, then connect the converter to the antenna jack on the back of your TV. We recommend using a 75-ohm cable to reduce interference caused by radio waves. R AUDIO (red) L AUDIO (white) VIDEO (yellow) Headphones To video out (yellow) To L audio out (white) To R audio out (red) Non-S-Video device Insignia NS-R20C Round Tube TV Connecting an S-Video device To connect an S-Video device: S-Video device To L audio out (white) To R audio out (red) To S-Video out Audio cable L AUDIO (white) R AUDIO (red) S-VIDEO 1 Plug an S-Video cable into the S-VIDEO jack on the back of your TV, then plug the other end of the cable into the S-VIDEO OUT jack on the S-Video device. 2 Plug the left and right audio cables into the AUDIO L and AUDIO R jacks on the back of your TV, then plug the other ends into the left and right AUDIO OUT jacks on the device. Using your TV Turning your TV on and off To turn your TV on and off: 1 Plug the power cord into a power outlet. 2 Press POWER. Note The power indicator turns off when your TV is active. The power indicator turns red when your TV is in standby mode. If your TV has a blue screen or a screen saver displayed, your TV goes into standby mode after five minutes. Selecting the TV signal source To select the TV signal source: 1 Press MENU. The on-screen display (OSD) opens. 2 Press MENU one or more times to highlight Tuning. 3 Press CH or CH to highlight SOURCE. 4 Press VOL or VOL on the remote control or VOL or VOL on the front of your TV to select AIR (outside antenna) or CABLE (cable TV). Memorizing channels When you memorize channels, your TV scans for available channels in your viewing area and stores the channel information in memory. To memorize channels: 1 Press MENU. The on-screen display (OSD) opens. 2 Press MENU one or more times to highlight Tuning. 3 Press CH or CH to highlight AUTO SEARCH. 4 Press VOL or VOL on the remote control or VOL or VOL on the front of your TV to start scanning for channels. This process may take several minutes. 5 If you want to stop scanning, press MENU. Deleting a memorized channel If you to skip a channel when you use a channel buttons, you can delete the channel from memory. To delete a memorized channel: 1 Tune to the channel you want to delete. 2 Press MENU. The on-screen display (OSD) opens. 3 Press MENU one or more times to highlight Tuning. 4 Press CH or CH to highlight DELETE CH. 5 Press VOL or VOL on the remote control or VOL or VOL on the front of your TV to select YES. Changing channels To change channels: • Press CH or CH . Or, press the number buttons to enter the channel number. For example, to select channel 12, press 1 then press 2. The c...