Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Do not install in a location where there is excessive dust, smoke or moisture. These sources can create a fire. Never apply unnecessary stress or load on the installed unit. Never hang on unit. Do not install unit alone. Safe installation requires at least two people. Do not route your flatscreen TV’s power cord in wall. Check local building/electrical codes for more information. Cautions To prevent eye fatigue, do not install where there is direct sunlight or excessive light. When carrying out maintenance, disconnect the TV’s power supply to avoid electrical shock. If planning to route AV cable in wall, only use cable UL-certified for this use. Pre-Installation Checklist ®• Does your mounting location have at least one wall stud? ®• Is your view of the mounting location free of glare or other obstructions? ®• Is the location of your wall stud or masonry surface suitable for repositioning your display? ®• Is your mounting location near an AC power outlet? Ideally, the outlet should be behind your TV. This will conceal your display’s power cord. ®• Is your mounting location at least 3 ft. from any source of heat or water? ..... To hide your TV’s power cord, install a Monster® In-Wall PowerCenter™ behind the placement of your display. Installing the Wall Mounting Plate Remove all pieces of the wall mounting system to ensure you have all the necessary parts. Wood Stud Mounting: ....................2) 1) Using an electronic stud sensor, locate a wall stud at your desired mounting location. With the help of a friend, position the wall mounting plate on the wall stud. Using the provided level, confirm that the wall plate is plumb or vertically straight. For best results, position the level horizontally with the narrow end flush against the side of the wall plate. Hold the plate firmly in place. 3) Mark the stud center in the top and bottom mounting holes with a pencil. 4) With your electrical drill and 3/16" bit, pre-drill a 3" deep hole at each mark. 5) Attach the wall plate to the wall using the lag bolts and round washers as shown below. Tighten each bolt with your electric drill or socket wrench. Turn clockwise until secure. DO NOT over tighten bolts. This can damage the wall plate or the surface of your wall. DO NOT release the wall plate until you are absolutely sure it is secured to the wall. .................................................................................................................................................................................. Installing the Wall Plate continuecontinued ....................2) Masonry Mounting Masonry mounting requires specialized knowledge, skills and tools. Monster highly recommends that you seek the help of a professional installer when mounting to masonry. DO NOT drill holes in masonry mortar joints. 1) With the help of a friend, position the mounting plate in the desired location. Using the provided level, confirm that the wall plate is plumb or vertically straight. For best results, position the level horizontally with the narrow end flush against the side of the wall plate. Hold the plate firmly in place. 3) Mark the centers of the top and bottom mounting holes with a pencil. Be careful not to mark a mortar joint. 4) With your electrical drill and 1/2" masonry bit, pre-drill a 3" deep hole at each mark. 5) Install the supplied plastic anchors in each hole. Tap into hole until fully seated. 6) Attach the wall plate to the wall using the lag bolts and round washers as shown to the right. DO NOT over tighten bolts. This can damage the wall plate or the surface of your wall. .................................................................................................................................................................................................. Setting Your Mount’s Adjustment Capabilities The SmartView 300S features a wide-angel swivel joint and all-directional O OOm mmn nni iiB BBa aal lll lll™for fine-tuning the position of your display. • The swivel joint enables you to turn your display left or right 160°.* • The OmniBall allows you to pivot your screen any direction and rotate it 360°. Before attaching your LCD TV to the four-point TV mounting plate, you can increase or decrease the O OOm mmn nni iiB BBa aal lll lll pivot action. 1) Slide the LCD TV mounting plate onto the wall plate as shown to the right. 2) By hand, remove the black plastic cap in the center of the mounting plate, revealing the O OOm mmn nni iiB BBa aal lll lll tension nut (13mm). 3) With a socket wrench (13mm or 1/2"), turn the tension nut clockwise to limit pivot and rotation. 4) Turn the nut counterclockwise to increase pivot and rotation. Your mount’s wide-angle swivel joint also has an adjustable tension screw. It can be adjusted before or after your TV is attached to the TV mounting plate. 1) Remove the plastic cap on the top of the swivel joint to access its tension screw. 2) With the included Allen wrench, turn the tension screw counterclockwi...