Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
BUTTON FUNCTIONS HYPER SURROUND Create a deep, 3-dimensional sound effect by channeling the sound through the TV’s front firing speakers. HYPER SURROUND HYPER SURROUND ON OFF TV/VIDEO TV/VIDEO controls the TV's input mode. TV/VIDEO TV VIDEO-1 VIDEO-2 Model AV-32015 has one Video input. TV VIDEO 100 + The 100+ button lets you access all channels above Channel 99. To move to Channel 124: 100+ 2 (two) 4 (four) VCR BUTTONS RM-C341 and RM-C345 ONLY. This remote will control your VCR. You can play, rewind and fast-forward, record, pause, stop, move channel up and down, and power on and off. Note: This remote is preset with the code 000 to control a JVC VCR. For any other brand, you must set up the manufacturer's code (page 12.) MUTING The MUTING button turns the sound off completely when you press it. Press it again to restore the volume to the previous level. RETURN+ There are two kinds of Return… R e t u rn+ — Set a “Return Channel” to re t u rn to after scanning with CH A N N E L - / + . RETURN+ and hold for 3 seconds RETURN CHANNEL PROGRAMMED ! Scan with CHANNEL -/+ RETURN+ Note: To cancel a Return channel, pre s s and hold Return+ for another 3 seconds until “RETURN CHANNEL CANCELLED!” a p p e a r s . Return — Return to the last channel viewed after moving to another channel via the 10 key pad. RETURN+ Move to another channel with the 10 key pad. RETURN+ Note: When PIP is on, the RE T U R N+ b u t t o n function affects only the main screen. NUMBER BUTTONS 10 KEY PAD Change channels with the 10 key pad. For example, to move to Channel 7: 0 (zero) 7 (seven) 27 NOTES : Hyper Surround and VCR buttons are available on the following models only: • AV-36050 • AV-36020 • AV-32050 • AV-32020 • AV-27050 You can find another discussion of Return and Return+ on page 11. 28 28 BUTTON FUNCTIONS NOTES: Picture in Picture is available on the following models only: • AV-36050 • AV-32050 • AV-27050 ON/MOVE (Picture in Picture) PIP allows you to view two pictures simultaneously. (PIP) ON/MOVE 02 07 EXIT to turn PIP off Note: The PIP channel and main screen channel will appear in the display momentarily right after you turn on PIP. You can leave them up permanently by pressing DISPLAY until you reach the mode. Note: The PIP Screen is 1/9 of the regular screen size. Once PIP is turned on, the ON/MOVE button operates the Move feature. You can move the PIP window to any of the TV’s four corners. ON/MOVE Note: Each press of the On/MOVE button will shift the PIP window one position. Note: When the PIP screen has no signal, the PIP window will be blue. FREEZE You can freeze the picture in the main screen into the PIP window. FREEZE Note: When the PIP is off, pressing FREEZE takes a snapshot of the main screen and puts it into the PIP window… great for catching those mail order addresses. Note: When the PIP is on FREEZE stops the PIP picture. SWAP You can swap the PIP picture and the main picture. SWAP CHANNEL –/+ For PIP Change the channel in the PIP window. CH –/+ SOURCE You can select the source for the PIP window. SOURCE TV V-1 V-2 PIP NOTES 50 Series models have 2 Tuner PIP and can see two signals at once. This means you can view two channels at the same time. In order for PIP to work, the TV must be set to "TV mode". If you use your VCR to play a video, the VCR will automatically switch your input to VCR mode. In VCR mode, the TV sees only one signal, that of the VCR. In order to view PIP, you then need to press the TV/VCR button on your VCR remote to switch back to TV mode. T R O U B L E S H O O T I N G CHECK PROBLEMS 29 No power • See if the power cord became unplugged. • Perhaps you have experienced a blown circuit breaker or fuse or a power outage. No picture or sound • The antenna could be disconnected. • The Input mode (TV or video) could not be set properly, refer to page 27. • The tuner mode (in the menu selection) could be set improperly, refer to page 15. • The station may be having difficulties, check to see if other channels are operating normally. Remote control is not operating • Check that the batteries are still working and properly installed. • Make sure there are no objects blocking a clear path from the remote to the TV. • Check that the 2-way mode selector switch is in the proper position — set to TV to view television. You cannot select a certain channel • Maybe you are too far from the TV, you must be within 23 feet (or 7 meters). • Make sure the channels are programmed. See Channel Summary, page 17. • Perhaps the channel is locked, select it with the 10 key pad and follow instructions. Power turns off • Perhaps the On/Off Timer is set, press the power button, check page 24. • The power was interrupted or the power cord unplugged. • The Sleep Timer may be set, see page 26. The clock is wrong PICTURE Poor color quality • The clock needs to be reset. See page 16. CHECK • Tint and color may be improperly adjusted. Check page 22. • Video Status mode may be set to an inappropriate setting. Check page 22. Lines ...