Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Certified to comply with ANSI A112.18.1M ASSE 1016 ROUGHING-IN DIMENSIONS Recommended Tools Flat Blade Screwdriver Phillips Screwdriver Remove as much surface dirt and film using clear water and soft cotton cloth (as described above). Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT 186mm (7-3/8) 100mm (3-7/8) 230mm (9) 230mm (9) 48mm to 68mm (2 to 2-5/8) 150mm (6) NOTE: FITTING MUST BE INSTALLED WITH VOLUME CONTROL ON TOP. R520 1/2" NPT INLETS or R540 3/4" NPT INLETS 25mm (1) FINISHED WALL 190mm (7-1/2) M 9 6 8 6 5 9 1 Remove PLASTER GUARD (1) if attached. Push CAPS (2 & 2a) as shown onto CONTROL VALVES (3). Push ESCUTCHEON (4) over CAPS (2, 2a) and flush against finished wall. Attach with the two SCREWS (5) provided. 1 TRIM INSTALLATION 2 INSTALL HANDLES Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: TRANSPOSED SUPPLY PIPING 3 OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim. (Reverse steps 1 and 2. CHECK STOP (RED TO BLUE) Turn the water supply back on and perform the temperature adjustment in step 4. Assemble HANDLES and TRIM. CHECK STOP (BLUE TO RED) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. 1 8 5 9 10 11 3 4 6 2 2a 3 TOP 1 5 7 Align HANDLE BASE (1) and push onto KNOB MOUNT (2). Install LEVER HANDLE (3) as shown. Install HANDLE SCREW (4) and tighten with screwdriver. Push INDEX CAP (5) into HANDLE (3). Install HANDLE ADAPTER (6) onto VALVE STEM (7). Install HANDLE SCREW (8) and tighten. Push VOLUME CONTROL KNOB (9) onto HANDLE ADAPTER (6). Use HEX WRENCH (10) supplied and tighten set screw to secure VOLUME CONTROL KNOB (9). Push in PLUG BUTTON (11). 2 4 M 9 6 8 6 5 9 4 4 4 TEMPERATURE ADJUSTMENT SET HOT LIMIT STOP Check that arrow marking B points to the 3 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 3 o'clock position. See Figure 1. For 100°F adjustment, turn the water supply on. Turn KNOB MOUNT (4) until the spout temperature is 100°F. Check that arrow "A" on the KNOB MOUNT (4) still points 3 o'clock position after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (4) by pulling it towards you while standing directly in front of the valve. Reinstall the KNOB MOUNT (4) with arrow "A" 3 o'clock position. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE. See step 3 for HANDLE (3) installation. Pull out index CAP (1) and remove HANDLE SCREW (2). Pull off HANDLE ASSEMBLY (3). ARROW "A" BLACK CLAMP ARROW "B" RED LOCKING DEVICE TEMPERATURE LIMIT STOP ARROWS AT 3 O'CLOCK POSITION Figure 1 KNOB MOUNT 112 109 104 1 2 3 M962636-YYY0A VOLUME CONTROL HANDLE TOWNSQUARE M 9 6 8 6 5 9 MODEL NUMBER CHROME BLACKENED BRONZE (PVD) SATIN NICKEL (PVD) 002 068 295 Replace the "YYY" with appropriate finish code HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800 442-1902 Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. A907090-YYY0A CAP M962635-YYY0A ESCUTCHEON AND SCREWS A918434-YYY0A ESCUTCHEON SCREWS M962633-YYY0A HANDLE SCREW AND INDEX BUTTON M908587-YYY0A HANDLE BASE M916815-YYY0A LEVER HANDLE © AS America, Inc. 2007 CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT T555740 CENTRAL THERMOSTAT WITH VOLUME CONTROL Installation Instructions M968255Rev.1.1 R520 Thank you for selecting American-Standard...the benchmark of fine quality for over 100...