Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. TOP / OBEN 168mm (6-5/8) 232mm (9-1/8) 86mm (3-3/8) 34mm (1-3/8) 180mm (7-1/8) 150mm (5-7/8) 48mm to 68mm (2 to 2-5/8) R510 1/2 NPT R530 3/4 NPT R510 1/2 NPT R530 3/4 NPT 25mm (1) 1 1 3 5 2 4 1 3 4 M968682 TEMPERATURE CALIBRATION SET HOT LIMIT STOP 5 Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards. For 100°F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100°F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow. Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE (5). ARROW "A" ARROW "B" 104 109 112 OPERATING THE VALVE 4 1 Push CAP (1) over the O-RING SEAL (2). TRIM INSTALLATION 1 3 7 5 8 6 If a temperature over 100°F is desired, pull the RED STOP BUTTON (1) away from the body of the MIXER UNIT and turn the TEMPERATURE KNOB. If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed. This will increase the mixed water temperature up to the maximum limit previously selected in step 4. Push ESCUTCHEON HOLDER (3) with lightly greased O-RING SEAL (4) over CAP (1). Attach with the two LONG SCREWS (7) provided. Attach ESCUTCHEON (5) to ESCUTCHEON HOLDER (3) with the two SHORT SCREWS (8) provided. Align pins in back of DIAL PLATE (9) with holes in ESCUTCHEON (5) and push DIAL PLATE (9) into place. 2 HANDLE INSTALLATION Push TEMPERATURE-CONTROL KNOB (1) (with the red stop on top) onto KNOB MOUNT (2). Install HANDLE SCREW (3) and tighten with screwdriver. Push KNOB CAP (4) into TEMPERATURE-CONTROL KNOB (1). GREASE ESCUTCHEON HOLDER O-RING SEAL 4 Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim CHECK STOP (RED TO BLUE) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step 4. CHECK STOP (BLUE TO RED) TOP / OBEN 2 2 M968682 MODEL NUMBERS CHROME BLACKENED BRONZE POLISHED BRASS SATIN NICKEL 002 068 099 295 Replace the "YYY" with appropriate finish code CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT A907143-YYY0A HANDLE CAP A918416-0070A SCREW A907080-YYY0A DIAL PLATE A918416-YYY0A ESCUTCHEON SCREWS A962628-YYY0A TEMPERATURE CONTROL HANDLE A907655-YYY0A ESCUTCHEON A907655-YYY0A ESCUTCHEON HOLDER SCREWS A907090-YYY0A CAP A953962-YYY0A ESCUTCHEON HOLDER TOP/OBEN T203.730 For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2008 HOT LINE FOR HELP MODEL NUMBERS CHROME BLACKENED BRONZE POLISHED BRASS SATIN NICKEL 002 068 099 295 Replace the "YYY" with appropriate finish code CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT A907143-YYY0A HANDLE CAP A918416-0070A SCREW A907080-YYY0A DIAL PLATE A918416-YYY0A ESCUTCHEON SCREWS A962628-YYY0A TEMPERATURE CONTROL HANDLE A907655-YYY0A ESCUTCHEON A907655-YYY0A ESCUTCHEON HOLDER SCREWS A907090-YYY0A CAP A953962-YYY0A ESCUTCHEON HOLDER TOP/OBEN T203.730 For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2008 HOT LINE FOR HELP ...