Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. 86mm (3-3/8) 34mm (1-3/8) 48mm to 68mm (2 to 2-5/8) R510 1/2 NPT R530 3/4 NPT R510 1/2 NPT R530 3/4 NPT 25mm (1) 220mm (8-5/8) 170mm (6-3/4) 1 3 5 2 4 M968025 TEMPERATURE CALIBRATION SET HOT LIMIT STOP 5 Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards. For 100°F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100°F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow. Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE (5). ARROW "A" ARROW "B" 104 109 112 OPERATING THE VALVE 4 2 HANDLE INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim CHECK STOP (RED TO BLUE) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step 4. CHECK STOP (BLUE TO RED) Turn on water supply on and test installed fitting. If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed. See step 3 for TRANSPOSED SUPPLY PIPING. Operate valve from off to cold to hot. Check temperature. If max mixed water temperature is to hot or to cold see step 4 and re-calibrate the valve. OFF COLD HOT 1 3 2 6 Install HANDLE ADAPTER (1) onto TEMPERATURE CONTROL KNOB (2) and tighten with SCREW (3). Align HANDLE (4) and push onto TEMPERATURE CONTROL KNOB (2). Tighten SET SCREW (5) in handle with HEX WRENCH (6) SUPPLIED. 5 6 1 TRIM INSTALLATION Push CAP (1) over the O-RING SEAL (2). 1 3 Push ESCUTCHEON HOLDER (3) with lightly greased O-RING SEAL (4) over CAP (1). Attach the FIXATION PLATE (7) to the ESCUTCHEON HOLDER (3) with the two SCREWS (5) provided. Push ESCUTCHEON (6) flush against finished wall. 2 5 7 GREASE ESCUTCHEON O-RING SEAL 4 M968025 MONENTS MODEL NUMBERS CHROME SATIN NICKEL 002 295 Replace the "YYY" with appropriate finish code CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT M908023-YYY0A ESCUTCHEON KIT A907090-YYY0A CAP T506.730 For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © AS America, Inc. 2008 HOT LINE FOR HELP M962727-YYY0A HANDLE KIT M918038-0070A ADAPTER M918990-0070A SELF TAPPING SCREW 023774-0070A ESCUTCHEON SCREWS M962630-0070A ESCUTCHEON HOLDER A924335-0070A FIXATION PLATE THERMOSTAT CENTRAL CONTROLE DE VOLUME JEU DE GARNITURE Installation Directives M968025 MOMENTS T506.730 Nous vous remercions d'avoir choisi American Standard… synonyme de qualite superieure depuis plus de 100 ans. Pour que l’installation se deroule sans probleme, veuillez lire attentivement ces instructions avant de commencer. Certifie conforme aux normes ANSI A112.18.1M ASSE 1016 MESURES RELATIVES AUX POINTS DE RACCORDEMENT Outils recommandes Tournevis a lame plate Tournevis Phillips Enlever autant que possible les saletes et le film a l’aide d’eau claire et d’un chiffon de coton doux (tel que decrit ci-dessus). Utiliser l’un des suivants pour enlever les films et les accumulations tenaces : Detergents liquides doux Produits de nettoyage pour vitres sans ammoniac Des liquides doux non acides, non abrasifs ou des produits ...