Assessments - , GPA:
(
)
)
Fabricante : Aube Technologies
Arquivo Tamanho: 895.58 kb
Arquivo Nome : TH110A-SP-P-120-D.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
TO SET TIME AND DAY Press on DAY, HOUR and MIN buttons to adjust time and day. TO RECORD THE (COMFORT) SETPOINT TEMPERATURE Select chosen setpoint temperature by using or button. Press on button (2 to 3 seconds) until icon appears on display. TO RECORD THE (ECONOMY) SETPOINT TEMPERATURE Select chosen setpoint temperature by using or button. Press on button (2 to 3 seconds) until icon appears on display . TO RECORD THE (VACATION) SETPOINT TEMPERATURE To program the Vacation temperature, select the desired degree using the buttons and press on the and buttons simultaneously until the icon is displayed (app. 3 seconds). OPERATING MODES To select an operating mode, use MODE button. AUTO: Runs the program. or shows temperature setting and can override temporarily your programming up to the next program. MAN: Maintains the selected temperature. or changes the temperature setting. MODEL TH110A-SP-P (120 V) uuuuuu NOTE : The "Problems and Solutions" section at the end of this user's guide will help you to correct your problems during the installation. This thermostat has been designed to operate with any installation which has a RESISTIVE load not exceeding 2400 W (20 A) @ 120 VAC such as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is not compatible with a low voltage controller used by a central heating system. Electricians or experienced technicians should install the thermostat. This thermostat is designed to be used with a self-protected heating system equipped with thermal cut off and circuit breaker. PARTS INCLUDED -One (1) TH110A-SP-P (120 VAC) thermostat -Two (2) 6-32 screws -Four (4) solderless connectors (for copper wire) TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of the thermostat clean and free from obstructions. 1) Connecting wires and mounting thermostat Connect the rear thermostat wires to the 120 V LINE and to the load using solderless connectors for copper wires. See schematic diagram. Push the excess wire back into the electrical box to prevent interference with the thermostat. Secure the thermostat using two (2) 6-32 screws. Once the thermostat is properly installed, return power to heating system. OLD THERMOSTAT LOAD SUPPLY BLACK BLACK BLACK WHITE BLACK BEFORE LOAD 120 V LINE 120 VAC 60 HZ B B W B W W W B AFTER NOTE : All cables and connections must conform to the local electrical code. WARNING: Special CO/ALR solderless connectors must be used when connecting with aluminum conductors. Power-up 2400 W (NI) @ 120 Vca Set the On/Stand by switch to On. When power is applied for the first time, the display must show the time 00:00, the room temperature and the Manual mode icon ( ). Other information might show up on the display if installation is defective or does not comply with the instructions. NOTE : The On/Stand by switch set to Stand by will place the thermostat in sleep mode. Ideal for summertime. 920-110-001-00-1-B 1/3 OPERATING MODES The TH110A-SP-P has two (2) operating modes. MANUAL ( ) This mode allows you to maintain a constant temperature in the room. 1-To activate this mode, press on Mode button to display the icon. 2-Set the desired temperature using the buttons or select the pre-programmed , or settings. (To select the setting, press on and simultaneously.) AUTOMATIC ( ) This mode executes your own programming. To activate this mode, press on Mode button to display the icon. The or icon indicates which temperature setting is used. Also, the icon of the program number will be shown. Memory back-up In the event of a power failure, an internal circuit will maintain the programming and the time. But only the time could have to be set if power failure is more than 2 hours. Early Start function The thermostat is providing a built-in function enabling it to calculate the optimum time to start the heating system to achieve the desired temperature setting at the programmed time. This function could start the heating system as early as 6 hours prior to the programmed time. To enable this function, set the switch E.S. to “ON” at the back of the thermostat. PROGRAMMING Programming the time and day 1- Set the time using the Hour and Min buttons. 2- Set the day using the Day button. Programming the Comfort, Economy and Vacation settings The Comfort , Economy and Vacation settings respectively represent the temperatures that you wish to have during the day , at night or while you are away at work , or while you are away for an extended period . To program your settings a) To program the Comfort temperature, select the desired degree using the b) c) buttons and press the button until the icon is displayed (app. 3 seconds). To program the Economy temperature, select the desired degree using the buttons and press the button until the icon is displayed (app. 3 seconds). To program the Vacation temperature, select the desired degree using the buttons and press on the and buttons simultaneously until the icon ...