Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
(See Figure 4, 5.) Ignore any wires which may be present, but which were not connected to the old thermostat. ¦ Refer to the Wiring Diagrams below to be sure your system is wired correctly. ¦ If your system is a single stage heat pump and uses an O or B wire, you must move the System Selector switch inside the thermostat to the Heat Pump position. If you have a normal furnace or electric system, leave the switch in the Standard position. Refer to the System Selector section for more information on this switch. ¦ Be sure to tighten the terminal screws securely, otherwise a loose wire could cause operational problems with your system or thermostat. ¦ Push excess wire back into the hole to prevent interference when installing the thermostat to the wallplate. ¦ Make sure the System Switch is set to OFF, and the Fan Switch is set to AUTO. ¦ Insert the bottom tab on the thermostat body into the slot at the bottom of the wallplate. Press the top of the thermostat body to snap it into the wallplate. Refer to Figure 6. (NOTE: Do not force the thermostat onto the wallplate, as the terminal pins may be damaged. If it does not snap properly, the thermostat may not work.) ¦ Insert the two AA size alkaline batteries, observing the polarity marked inside the battery compartment. ¦ Switch on the main power at the panel or furnace. Figure 4 Figure 5 Figure 2 Y1 W/B Y/O Rh Rc G Figure 3 G Rc Rh Y/O W/B Y1 x RH Figure 6 ® Wiring Diagrams 4-wire Heat/Cool System JumperWallplate Terminals Fan Relay Cool Contactor Heat Relayor Valve 24V SupplyHeat/Cool RhRcY/OW/BY1GX X 5-wire Heat/Cool System No JumperWallplate Terminals Fan Relay Cool 24V Supply Heat Relayor Valve Heat 24V Supply RhRcY/OW/BY1GCool Contactor X Single-stage Heat Pump System Jumper X OR Heat Mode Cool Mode Wallplate Terminals RhY/OW/BRcGFan Relay ReversingValve CompressorContactor Y1Heat Pump24V Supply Connect to Proper Reversing Valve Terminal. See Table A 2-wire Heat Only System Wallplate Jumper Terminals G Y/O Y1 XX X RhRc X W/B Heat 24V or Millivolt Supply Heat Relayor Valve 3-wire Heat Only System Jumper XX Wallplate Terminals Fan Relay RhRcY/OW/BY1GHeat 24V Supply X Heat Relayor Valve 3-wire Cool Only System RhRcY/OW/BY1GJumper XX Wallplate Terminals Cool Contactor Cool 24V Supply Fan Relay X X - No Connection System Selector STD– HP System Selector STD– HP System Selector STD– HP System Selector STD– HP System Selector STD– HP System Selector STD– HP Selector Switches In order for this thermostat to control your system, the system type must be specified by the selector switches on the printed circuit board inside the thermostat. ¦ Heating System Selector (HG - HE switch) The factory position for this switch is in the “HG” position. Leave it in this position if you have a gas furnace or an oil burner. If you have an electric furnace, test to see whether the Heat and Fan come on as expected after installation. If the Fan operation is normal, leave it in the “HG” position. If the Fan does not come on within a minute of the thermostat calling for heat, change the switch position to “HE”. The system selector has no effect in the cooling mode. NOTE: “HG” position is for gas and most other systems. “HE” position is for certain electric systems having a fan relay. ¦ System Selector (STANDARD - HEAT PUMP switch) The factory position for this switch is in the STD position. Leave it in this position if you have ANY system that uses gas, oil, electric, or hot water heating. If you have a single-stage Heat Pump (no auxiliary or emergency heat source), then slide the switch to the HP position. Be sure the reversing valve wire is connected to the correct terminal for your heat pump (Y/O) or (W/B). ¦ Auto Recovery selector (DISABLE / ENABLE) Your thermostat is set from the factory with the Auto Recovery Feature enabled, which complies with the EPA ENERGY STAR® Program. If you prefer to use normal recovery, slide the switch to the DISABLE position. Auto Recovery (SW4) System Selector (SW5) Fan Option (SW6) Figure 7 STD HP DISABLE ENABLE HG HE F° / C° Selection (Fahrenheit / Celcius) Your thermostat is set for F° mode from the factory. To change to C° mode, follow these steps: ¦ Press and hold the Up key. ¦ Use a paper clip to press the reset key. ¦ Once all the LCD segments turn on, release the Up key. NOTE: To return to F° mode, press the reset key with a paper clip. Do not press any other keys during the reset process. All programs and settings will be lost when pressing RESET. OPERATION Setting Day and Time ¦ The LCD will show this information when batteries are first installed, or after the Reset button is pressed. The temperature will update after a few seconds. ¦ During time and day setting mode, the temperature and program displays will go blank. ¦ Example: Set the Thermostat to the current time of 2:16 pm on Saturday. Refer to the Steps below. M AM 4 TEMP STEP 1: day/time ¦ Press to enter time and day setting mode. M The current hour and the AM / PM indicator AM wil...
Este manual também é adequado para os modelos :Os termostatos - 44260 (309.45 kb)
Os termostatos - 44260 (309.45 kb)