Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
The TH113-R is specially designed to control a floor heating installation, a baseboard or a convector. The TH113-R regulator operates like a dimmer switch to allow you to easily adjust the amount of power sent to your heating system. It features an integrated GFCI, and includes a test button and warning light for added security. This regulator is also equipped with an ON/STANDBY switch making it possible to put it in sleep mode when its use is not required (e.g. summer). IMPORTANT! The GFCI and Remote Input options are not available with a low voltage power base. Skip sections 3 and 4. Align the bracket tabs on the regulator with the holes located on the power base. .. This regulator must be installed on a PB112 power base. .. The screw cannot be removed completely. .. Keep the regulator’s air vents clean and free from obstructions. The TH113-R regulator operates on perpetual 15-minute heating cycles. For example, if the dial is set halfway, the system will heat for 50% of the cycle; it will be ON for 7.5 minutes and OFF for 7.5 minutes. Below is a detailed table of the cycle duration based on the dial’s position: NOTE: Depending on the power base used, the heating cycles can be 15 seconds or 15 minutes. Power Selection Dial On/StandBy Switch GFCI Test and Warning Light Control Module Power Base Position and equivalent % I 0% 2 20% 4 40% 6 60% 8 80% 10 100% ON 0 min 3 min 6 min 9 min 12 min 15 min OFF 15 min 12 min 9 min 6 min 3 min 0 min The GFCI monitors the electrical flow for any loss of current; if there is any loss, the thermostat will cut off power to the heating system. We recommend you test the GFCI immediately after installing the control module, and once a month thereafter to ensure it is operating properly. To test: .. Press the TEST button: • Successful: TEST warning light is ON and power to heating system is cut off. • Unsuccessful: TEST warning light is OFF. Cut power to heating system from the main power panel and call customer service. .. When successful, reset thermostat (STANDBY/ON) to power heating system. NOTE: If the test warning light comes ON during normal operation, cut power to heating system from the main power panel and have an electrician verify the installation. When a remote control interface (Aube CT241 or any other remote control system) is connected to the power base’s remote input and a signal is received, the TH113-R module automatically lowers the percentage by 35% based on the dial’s current position. The LED lights up to indicate the signal’s presence (except for GA and GB models). .. The TEST button can be used to bypass the signal for a 2-hour period. The LED goes off to indicate the bypass. NOTE: When combined with a GA or GB power base, the TEST button is used only for GFCI testing. The percentage is decreased, but the bypass function and indicator are not available. Model: TH113-R Power setting range: 0 to 100% Storage: -20°C to 50°C (-4°F to 120°F) AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY This product is guaranteed against workmanship defects for a one year period following the initial date of purchase. During this period, AUBE Technologies Inc. will repair or replace, at our option and without charge, any defective product which has been used under normal conditions. The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation. This warranty cancels and replaces any other manufacturer's express or implied warranty as well as any other company commitment. AUBE Technologies Inc. cannot be held liable for related or random damages following the installation of this product. The defective product as well as the purchase invoice must be returned to the place of purchase or mailed, prepaid and insured, to the following address: Aube Technologies Inc. 705 Montrichard Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8 If you have any questions concerning the TH113-R Regulator, call our technical support team at: Monday to Friday from 8:30 AM to 5:00 PM EST. For more information on our products, visit us at: !"#$ % & ' ( ! ) ' Phone: Montreal area: (450) 358-4600 Canada / U.S.: 1-800-831-AUBE (2823) Fax: (450) 358-4650 Email: service@aubetech.com 05/11/03 400-113-004-A PB112-024T-15S Installation Instructions 24 V Low-Voltage Power Base • Install the control module onto the base. • Applications • Apply power to the heating system. The PB112-024T-15S power base can be used on any TH11x series • Verify the installation by checking that the heating system can be thermostat (with the exception of the TH110 model). This low-voltage turned on or off using the thermostat. power base operates on 15-second cycles and can be connected to a line-voltage load using a solid-state relay. The PB112-024T-15S is compatible with most solid-state relays; however, the following Aube 4.1 Single SSR with Built-in Transformer relays are opt...