Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Disconnect power before beginning installation. Must be installed by a certified electrician. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. Need Help? For assistance with this product please visit or call Honeywell Customer Care toll-free at 1-800-831-2823. Installation Guide Installation Guide The equipment interface module (EIM) allows you to control a baseboard heater, a convector or a fan-forced heater in a 120-volt, 208-volt or 240-volt application from a EConnect™ wireless thermostat. Remote control Thermostat Outdoor air sensor Thermostat EIM in remote junction box EIM in heater Electrical panel Heater Supply wires Wireless connection Installation procedure • Install the equipment interface module (EIM)............................................... Pages 3 - 6 • Install batteries in wireless devices..................................................................... Page 7 • Link all devices to wireless network ........................................................... Pages 7 - 10 • Exit wireless setup .............................................................................................Page 11 • Customize thermostat (installer setup)......................................................Pages 11 - 18 • Mount thermostat and outdoor sensor ..................................................... Pages 19 - 20 For error codes, see page 20. To verify the signal strength, see page 21. To replace a wireless device, see pages 21-22. For specifications and replacement parts, see page 23. SAVE THESE INSTRUCTIONS 2 EConnect™ TA7210 • Install the Equipment Interface Module (EIM) 2. Determine the location The equipment interface module (EIM) consists of a relay and an antenna. They can be installed either in the wiring compartment of the baseboard heater or in a 4-11/16” square junction box. Install EIMs at a minimum distance of 2 feet (0.6 m) of each other. This minimum distance still applies even if the EIMs are on opposite sides of a wall. • Installing the EIM in a baseboard heater You can install the EIM in the wiring compartment of the baseboard heater if you have any of the heaters listed in the following table: Relay Antenna Manufacturer / brand Series Cadet F Global Commander CCB King Electrical K, CB, KP, M Marley 2500, BKOC, QMKC Ouellet ODBA, ODI, ODIA, OFM, OPR Stelpro CBB, N, SCA, SCAS TPI 2900C, 2900S, 3700, 3900 The product has been tested for compatibility with the heaters listed above. If your heater is not on the list, install the EIM on a 4-11/16” square junction box or replace it with one listed. • Installing the EIM in a 4-11/16” square junction box You can use a 4-11/16” square junction box in either of the following conditions: • You have a convector or fan-forced heater. • You cannot install or do not wish to install the EIM in the wiring compartment of the baseboard heater. The junction box can be installed anywhere in the Relay Antenna house; for example, near the main electrical panel. 3 Installation Guide 4 Installation in a baseboard heater ELECTRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect AC power before beginning installation. Wiring must comply with local electrical codes. Use special CO/ALR solderless connectors if supply wires are made of aluminum. Disconnect the heater wires from the supply wires. If the heater has a built-in thermostat, remove it. 1) Remove the knockout on the side of the heater. 2) Remove the locknut from the antenna and peel off the adhesive backing. Feed the antenna cable through the knockout and install the antenna vertically as shown. Put the locknut and tighten. 3) Clean the back panel inside the wiring compartment where the relay will be installed. Peel the adhesive backing off the relay and stick the relay on the back panel. 4) Connect the heater wires and the supply wires to the relay. See page 6 if you are connecting more than one heater. 5) Insert the antenna plug into the relay receptacle until you hear a click. 6) Put the heater cover back. (If a built-in thermostat was removed, install one of the supplied plugs to cover the hole on the existing cover.) Apply power to the heater. Do not install the antenna cover yet. ELECTRICAL HAZARD Can cause electrical shock. Install heater cover plate before applying power. Relay wires must be at the top L2 L1 : For 240V application N L : For 120V application Blue Black Red Install plug if applicable. EConnect™ TA7210 5 Installation in a 4-11/16'' square junction box ELECTRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect AC power before beginning installation. Wiring must comply with local electrical codes. Use special CO/ALR solderless connectors if supply wires are made of aluminum. 1) Mount the junction box on the wall. Punch out knockout(s), install strain relief bushing(s) and feed the supply wires and the heater wires. Punch out another knockout to ins...