Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
. This blood pressure monitor is only suitable for measuring the blood pressure of adults. . This blood pressure monitor measures blood pressure on the basis of the pulse rate. If you have a very weak or irregular pulse, the blood pressure monitor may not be able to determine the right blood pressure value. . Diabetics and people who suffer from cardiac arrhytmia, vascular constriction or liver disorders must consult their doctor before they start measuring their own blood pressure, since their blood pressure values might deviate from normal values. Pregnant women should also consult their doctor first. . If in doubt, consult a doctor. . Only a doctor is capable of interpreting your blood pressure values. Never change your medication without consulting a doctor. . Your blood pressure may fluctuate during the day and it may even vary within minutes.This means that successive measurements may show different values. . If the blood pressure monitor has been stored at a very low temperature (close to freezing point), put it in a warm place for at least one hour before using it. Important ENGLISH4 ENGLISH Before the first measurement C C 1 2 3 Remove the protective foil from the display. Open the battery compartment and place 2 AAA (LR03) batteries in the compartment. Make sure the + and - poles are pointing in the right direction. Push the + pole in first. Measuring the blood pressure Conditions for accurate blood pressure measurement . Sit down and relax for 10 minutes before you use the blood pressure monitor. Breath deeply in and out five times before you start measuring. . Wait at least 3 minutes between 2 measurements to avoid incorrect readings due to the temporary congestion of the arteries. . Perform the measurement every day at the same time, since your blood pressure fluctuates in the course of the day. . Do not eat, smoke or drink before you measure your blood pressure.Alcoholic beverages in particular will influence the measurement. . Do not attach too much importance to the results of a single measurement. Performing ENGLISH measurements regularly over a longer period of time and recording the results will give you a better insight into your blood pressure than a single measurement. Performing the measurement 1 Put the wristband on the left wrist with the control panel on the inside of the wrist. Make sure there is no piece of clothing between the wrist and the wristband. C The wristband must be placed approx. 1 cm (0.5 inch) away from the palm of the hand. 1 Tighten the wristband firmly around the wrist. Make sure there is no room left between the wrist and the wristband. C . The coloured marks on the wristband indicate a wrist circumference of 13.5 - 22 cm (5.3 - 8.3 inches). If the marks do not overlap, the circumference of your wrist is too large or too small to allow this blood pressure monitor to function accurately. 2 Sit down comfortably and hold your wrist at the same height as your heart. C If you expect your systolic pressure to exceed 150 mmHg, read the instructions under the heading 'Systolic pressure higher than 150 mmHg'. ENGLISH C . When the measurement has been completed, the cuff is automatically deflated.Your systolic pressure (SYS), diastolic pressure (DIA) and pulse (PUL) are now shown on the display. C Press the START button. 3 All symbols appear on the display for a moment. The wristband inflates automatically and the display shows that the pressure is increasing. When the correct pressure in the wristband has been reached, inflation of the wristband stops and the measurement starts. The blood pressure monitor will automatically increase the pressure in the wristband if the pressure in the wristband turns out to be too low during the measurement. Remain seated in a relaxed way. . The pressure in the wristband will slowly decrease during the measurement. This is shown by the counting down of the pressure on the display. Note: do not talk, cough, laugh or move your arm or hand muscles during the measurement. Systolic pressure higher than 150 mmHg If you switch the appliance on in the normal way, the wristband will be inflated to 180 mmHg. 8 ENGLISH C C If your systolic pressure is higher than 150 mmHg, the appliance will have to interrupt the measurement in progress in order to inflate the wristband to the correct pressure.This will cause your wrist to be squeezed tight for quite some time.You can avoid this inconvenience by inflating the wristband to the correct value straight away. 1 To inflate the wristband to the correct value: keep the START button pressed in until the value shown on the display is 40 mmHg higher than your expected systolic pressure. B Example: if you expect your systolic pressure to be 160 mmHg, keep the Start button pressed in until the value shown on the display is 200. Memory function The blood pressure monitor automatically stores previously measured values in its memory. Up to 60 measurements can be stored. 1 Retrieve data from the memory by pressing ...
Este manual também é adequado para os modelos :Monitores de pressão arterial - HF319 (376.69 kb)
Monitores de pressão arterial - HF321 (376.69 kb)