Assessments - 3, GPA: 4.3 ( )

Fabricante : Panasonic Arquivo Tamanho: 7.79 mb Arquivo Nome : EW3122.pdf Língua de Ensino:

• You unconsciously bent your elbow. • The upper arm became very tense. • You moved your arm. • Etc. Return to the proper posture. o Lit Beep beep (short buzzer sounds) A movement which will cause large differences in measurement values occurred. • Body movement was large. • Body movement occurred several times. • Arm movement was large. Remeasure (Remeasure mark E is shown.) • It will also be lit in the following cases: • Pressure cuff tape fastener became unfastened. • Tube came out. • Etc. (For details, see p. 28.) * This function is intended to help ensure correct measurements. (See p. 26.) Even if the remeasure mark does not appear (or body movement indicator lamp does not light), it is recommended that 2 or 3 measurements be taken in a quiet condition for best results. 16 Alarm function signals high blood pressure Blood pressure values for both systolic and diastolic readings are determined and indicated via a three-color LED system as being within normal or hypertensive ranges based on definitions and classification of blood pressure levels by the JNC 7. Moreover, when blood pressure is in the high range, the reading displayed on screen flashes on and off to alert user. According to JNC 7 Classification, values consistently in excess of 140 mmHg (Sys.) and/or 90 mmHg (Dia.) are considered to constitute high blood pressure. 3 color light system ■ Hypertension ■Prehypertension ■ Normal i Blood Pressure Sign ■ Prehypertension I Normal LED Color Diastolic (mmHg) Orange 90 Yellow 80 Green Hypertension (Stage 1, Stage 2) Prehypertension Normal 120 140 (mmHg) Systolic Blood pressure readings will flash for approx. 6 seconds when in the high blood pressure range. Systolic blood pressure: 140 mmHg and over Diastolic blood pressure: 90 mmHg and over (Only when measurement is complete) If measurements could not be taken properly The remeasure mark E will be displayed. When taking successive measurements, press the Start/Stop button to switch off the blood pressure monitor once and stay quiet for 4 to 5 minutes, and then take the next measurement. Advice: In general, blood pressure measurements are lower for the second measurement because you are less nervous and are more tranquil. For people who easily get tense, measuring twice each time is very effective. When two measurements are taken, normally the smaller measurement is stored. When taking two measurements, always stay quiet for 4 to 5 minutes after the first measurement before taking the second measurement. 17 STORING MEASUREMENT VALUES This product can separately store 42 measurements each for two persons. Panasonic SYSL DIA. mmHg Puh/min. 8/ 3 15:3a 13 в вг вг вэ ■нурвлвгаол ПРгеЛлшвгеКл 1 iNma H шя On/Off Start Panasonic SYS. ™,Hg DIA. mmHg Pulgfonhi 0/ 3 /5:30 /за вг вг (9i “чг 1 On/Off Start After measurement, the f?l f2l will light. Press the Memory/Recall button with the number corresponding to the person for which measurements should be stored. Example: Person A: Press Person B: Press (21 M/R Storing is completed. • Up to 42 measurement values can be stored. When the memory is full and additional values are stored, the oldest value in memory will be deleted and the new value will be stored. • If measurements could not be taken properly (the E mark Is shown instead of the blood pressure value), measurement values cannot be stored. • However, even if the £ mark Is shown for the blood pressure value, the pulse value will still be stored. Number of stored data To erase all measured values stored in memory: 1. Press the Memory/Recall button for the person whose data you want to delete. The stored measurement values will be displayed. 2. Press the same Memory/Recall button again, and hold it pressed until the measurement values disappear (approximately 3 seconds or more). * It is not possible to erase single measurement values. To switch off the blood pressure monitor, preSS the On/Off Start button. • If you forget to switch It off, the blood pressure monitor will switch off automatically after approximately 5 minutes. 18 RECALLING STORED MEASUREMENT VALUES Measurements can be recalled after measurement is completed or after the power has been switched off. • If no measurement values are stored, no value will be shown. Press the Memory/Recall button for the person whose data you want to recall. 1 Panasonic SYS. maHg DIA. imHg PlMlh W 3 ¡5:30 BB 8? s? I?) ÏH? The average of all measured values In memory will be shown. • EEl will be shown at the bottom of the display. • For example, if 42 measured values are stored, the average of the 42 measurements will be shown. (If only 1 measurement Is stored, the ES78 will not be shown.) • The blood pressure Indicator lamps will light (for approximately 6 seconds). 1 Press the Memory/Recall button again. Each time you press the Memory/Recall button, the previously stored measurement values will be shown In...

Baixe o seu

Para fazer o download, introduza 2 dígitos :