Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
warranties all parts to be free from defects in material and workmanship for a period of one year from the date of shipment from our facility. This guarantee is based upon equipment being used 8 hours per day, or 40 hours per week, or in any increment which does not total more than a single shift operation, or 2,080 hours per year. Warranty will be reduced proportionally. This warranty does not cover part failure caused by lack of normal maintenance, abuse or misuse of the equipment. PERFORMANCE GUARANTEE All equipment manufactured by UniVersal Labeling Systems, Inc. carries a 30 day performance guarantee. If your machinery does not perform as described in our quote to you, UniVersal must be notified within 30 days of your dissatisfaction and we will make every attempt to correct it. If after a reasonable period of time, the machine does not meet the specified performance, we will take your machine back and reimburse you in full. Warranty Assembly and Operation Drawings Layout, Main Exploded View (conveyor) Exploded view BASE Conveyor Assembly, Applicator Crank Micro Adjustor Sensor Mounting Bracket SBK Wipe Down WPD-500 R320 Elect. Control box R320 Control Box Electrical Schematic Product Spacer Turning Unit BOM Turning Unit Mounting Assy CP-1000 Electrical Schematic L15 MODEL R-320 ASSEMBLY AND OPERATING INSTRUCTIONS Conveyor Height can be adjusted from your system’s specified height by adjusting the leveling pads RE-TIGHTEN LOCKING BOLT AND ANGULAR BRACE, BEFORE REMOVING SUPPORT AT BOTH ENDS OF CONVEYOR. FAILURE TO RE-TIGHTEN THE LOCKING SCREW ON SLIDING SLEEVE COULD RESULT IN THE CONVEYOR AND ATTACHMENTS DROPPING, CAUSING SERIOUS DAMAGE TO THE SYSTEM. SEE APPLIER INSTRUCTION MANUAL FOR PROPER OPERATION OF APPLIER HEAD AND WEBBING. TO ADJUST SYSTEM FOR INDIVIDUAL CONTAINERS, PROCEED AS FOLLOWS: 1. Selecting the container to be labeled, place on conveyor for reference and adjust vertical height of turning unit so that belt is centered vertically on container. 2. Adjust vertical height of guide rails opposite the applier and turning unit to center on product but never low enough that rail drags on conveyor top. 3. Adjust guide rail across conveyor so that container is encapsulated securely between the turning belt and the sponge backing plate. Move container along belt of turning unit to establish that the sponge backing is adjusted parallel to belt. This is important, as container must be controlled by turning unit and sponge backing on guide rail. 4. With applier head turned off, turn on conveyor. Set speed control by knob on control box on front of conveyor to maximum speed. 5. Turn on turning unit by on-off switch located on control box on top of unit. (NOTE: This unit’s power cord is to be plugged into control box on front of conveyor). Adjust speed of turning unit so that turning belt is moving at a slightly higher rate of surface speed than conveyor. 6. Place container on conveyor on entrance end and allow to proceed through turning unit. 7. When it is considered that the container is being properly controlled and guide rail adjustments are proper, select the appropriate label; place roll on applier and web properly. Refer to applier instructions. MODEL R-320 ASSEMBLY AND OPERATING INSTRUCTIONS 8. Stop conveyor by turning speed control to “O”. Turn off turning unit. Plug power cord of applier into control box on front of conveyor. (NOTE: Applier and turning unit will not receive power with switch on control box on front of conveyor in OFF position). 9. Raise or lower applier so that label is centered on container. Label web must always run to lower edge of peeler bar on this system, with edge of peeler bar clearing top of conveyor EDGE. DO NOT LOWER APPLIER TO THE POINT WHERE EDGE OF PEELER BAR IS RESTING ON TOP OF CONVEYOR EDGE. 10. Adjust peeler bar so that back side clears turning belt by no more than 1/8”. 11. Turn on master switch on applier, then turn on motor switch; one label will advance. 12. Product sensing micro switch is secured to edge of guide rail with arm extending through guide rail. Activating this switch by hand will cause applier to deliver a label. NOTE: Position label at end of peeler bar and adjust star wheel on applier so that 1/8” to 1/4” of label is extending beyond peeler bar edge when label is delivered and applier stops delivering a label. Trigger applier head with product sensing several times to allow web to track properly and to observe extension of label beyond peeler bar. YOU SHOULD NOW BE READY TO LABEL Turn on conveyor by speed control knob and adjust to just below maximum speed. Turn on turning unit. Speed control knob on applier should be set at approximately 65 on dial - - with turning unit at approximately the same setting. With all systems running - - Place container on conveyor and NOTE: 1. Point at which product switch activates relative to position of container. The ideal point of which the applier starts delivering the label is as the container contacts t...