Assessments - 6, GPA: 4.3
(
)
)
|
Facilidade de uso
During this process a series of brief “ticks” indicates that reading is proceeding correctly. ADVANCED FORMATTING NOT FOR PEN INTERFACES • CONCATENATION • • ADVANCEDFORMATTING • Please follow the setup procedure carefully for these parameters. NOTE The Advanced Formatting parameters may not be compatible with the IBM USB POS interface selection. NOTE 1. Read the Enter Configuration code ONCE, available at the top of page. 2. Read configuration codes precisely following the numbered procedure given. = Read the code and follow the procedure given • = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of page. Enter Configuration Exit and Save Configuration I$+;I ADVANCED FORMATTING I$-?I CONCATENATION .. disable IEI0aI enable IEI1dI Permits the concatenation of two codes defined by code type and length. It is possible to set a timeout for the second code reading and to define code transmission if the timeout expires. The order of transmission is CODE 1-CODE 2. Define Concatenation Code 1 code ID IEK0eI Read the code type from the Code Identifier Table beginning in Appendix B. code length IEL0gI Read a number in the range 01-99 from the Hex/Numeric Table. Exit and Save Configuration ADVANCED FORMATTING I$-?I Code 2 code ID IEK1hI Read the code type from the Code Identifier Table beginning in Appendix B. code length IEL1jI Read a number in the range 01-99 from the Hex/Numeric Table. Concatenation Result Code ID use code 1 ID IEN0kI use code 2 ID IEN1nI Since you can concatenate codes from different families, you must select the Code ID character of the resulting code. The Code ID character will be sent in the output message only if it is enabled according to the Code Identifier selection (Datalogic, AIM, or Custom). Concatenation Timeout timeout IEJ3I Read two numbers in the range 00 to 99 00= no timeout 01-99 = timeout from 1 to 99 seconds Define the timeout, which determines the valid waiting period between the two codes, in order to accept concatenation. If the timeout expires, the resulting action will be based on the following selection. (HHDII) Exit and Save Configuration ADVANCED FORMATTING I$-?I Transmission after Timeout no code transmitted after timeout IEM0iI only code 1 transmitted (if read) after timeout IEM1lI only code 2 transmitted (if read) after timeout IEM2oI either code 1 or code 2 transmitted after timeout IEM3rI ADVANCED FORMATTING ADVANCEDFORMATTING Advanced formatting has been designed to offer you complete flexibility in changing the format of barcode data before transmitting it to the host system. This formatting will be performed when the barcode data meets certain criteria, which you will define in the following procedure. Up to 4 advanced code management formats can be defined and saved in memory. For each format you must complete the entire configuration procedure: Define another? Step 5 Divide Code into Fields Steps 7 - 8 Add up to 2 Additional Fields Step 1 Begin Format Definition 1, 2, 3, or 4 Step 6 Define Code Fields Steps 2 - 4 Define Match Code Conditions Step 9 Define Field Transmission Step 10 Apply or Not Standard Message Formatting Read the Enter Configuration Command Step 11 End Format Definition 1, 2, 3, or 4 YES NO Enable Advanced Formats 1, 2, 3, 4 Define No Match Result Read the Exit and Save Configuration Command Enter Configuration Exit and Save Configuration I$+;I ADVANCED FORMATTING I$-?I Begin Format Definition begin Format 1 definition IHA0TI begin Format 2 definition IHA1WI begin Format 3 definition IHA2ZI begin Format 4 definition IHA3]I Match Code Type match code type IHB&I Read the above code + the code type to match from the Code Identifier Table in Appendix B. OR any code type IHB0VI Match Code Length match code length IHC(I Read the above code + two numbers in the range 01 to 99 for the exact code length. OR any code length IHC001I Exit and Save Configuration ADVANCED FORMATTING I$-?I Match with Predefined Characters no match IHD0HE00AI OR match with 1 character IHD1]I match with a 2-character string IHD2`I match with a 3-character string IHD3cI match with a 4-character string IHD4fI After selecting the predefined match code, read the character(s) from the HEX table. Range of characters = 00-FE. Example: Match code with the 2-character predefined string = "@@". Match with a 2-character string Read + 40 + 40 AND position of first character in predefined string IHE,I Read the above code + two numbers in the range 01 to 99 representing the character position in the code where the first character of the predefined string must be found. Read 00 if the match string can be found in any character position. See par. 5.8.1 for details. 4 116 Exit and Save Configuration ADVANCED FORMATTING I$-?I Divide Code into Fields divide code into fields IHF.I Read one number in the range 1 to 5 to divide the code into fields. Define Code Fields define code fields Each code field length can be set by either: a) defining a field separator cha...
Este manual também é adequado para os modelos :Equipamentos de Loja - POWERSCAN D8330 (1.75 mb)