Assessments - 3, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
12. Press SET to start printing. • Both DATA 1 and DATA 2 print in both the upper print area and the lower print area of the disc. 13. After printing is complete, use and to select EXIT, and then press SET. 14. In response to the confirmation message that appears, press SET. ¦ To perform tape demo printing 1. Make sure a tape cartridge is loaded in the printer. • See page 13 for the Startup Guide for information about loading tape cartridges. 2. If the printer is on, press to turn it off. 3. Press to turn on the printer. 4. Press FUNCTION and then SET UP. 5. Use and to select DEMO PRINT, and then press SET. 6. Use and to select TAPE, and then press SET. 7. Use and to select PRINT, and then press SET. 8. Confirm that 1 is specified for the number of copies and CONT HALF CUT is specified for the tape cut mode. • You can change the number of copies and the tape cut mode (page 38) settings if you want. • If you are using a non-standard type of tape, select the appropriate tape cut mode (page 38) for the tape you are using. 9. Press SET to start printing. • The demo print contents depend on the width of the tape cartridge currently loaded in the printer. 10. After printing is complete, use and to select EXIT, and then SET. 11. In response to the message that press SET. E 56 Reference Power Requirements You can run the printer by using its bundled AC adaptor to plug it into a power outlet. It can also run on commercially available alkaline batteries. ¦ Using Batteries Note • The printer can run on eight AA-size alkaline batteries. Be sure to use alkaline batteries only. 1. Turn over the printer and remove the battery cover. • Never bend or twist the battery cover, or otherwise subject it to rough handling. Doing so creates the risk of printer malfunction. 2. Load a set of eight new batteries. • Make sure the positive g and negative h poles of the batteries are facing in the proper directions. 3. Replace the cover. Important! • The printer may suddenly turn off during printing if battery power goes low. Because of this, use of the bundled AC adaptor is recommended to power the printer. • Because of the affect cold has on batteries, the “LOW BATTERY!” may appear prematurely when the temperature is below 10°C(50°F). If this happens, move the printer to a location where the temperature is within the operating temperature range (10°C to 35°C (50°F to 95°F)) Battery Life Disc Label Printing • Printing of approximately 150 discs* Normal temperature (20°C (68°F)), one printing per disc. Label Tape Printing • Printing of approximately two 18mm tape cartridges under standard printing conditions* * When printing text or graphics that contain large areas of black, and printing under cold temperatures can shorten battery life for both disc label printing and label tape printing. 57 E Caring for the Printer Disc and tape label can become print head and rubber roller become dirty. Perform the following steps to clean the head and rubber roller. ¦ To use a cotton swab for cleaning Important! • Use only a cotton swab or some other soft material to clean the print head and rubber roller. Use of a very fine type cotton swab is recommended. 1. Press the cassette cover release and open the cover. • If a tape cartridge or the ink ribbon cassette adaptor is loaded in the printer, remove it. 2. Use a cotton swab moistened with alcohol to thoroughly swab the areas where the print head and rubber roller come into contact. Pr int head Rubber roller • You can rotate the rubber roller by pressing FUNCTION and then FEED. • You can also use a commercially available cassette tape recorder head cleaning kit to clean the print head. E 58 ¦ To clean with Note • Use an optionally cleaning tape (this procedure. 1. Press the cassette cover release and open the cover. • If there is a tape cartridge or ink ribbon cassette adaptor loaded printer, remove it. 2. Load the cleaning tape into the printer. 3. Press to turn on the printer. 4. Press FUNCTION and then FEED to feed the tape one or two times. • For details about using the cleaning tape, see the instructions that come with it. Cleaning the Printer Exterior Wipe the exterior of the printer with a cloth moistened with plain water. Wring all excess liquid from the cloth before wiping the printer. Never use benzene, alcohol, thinner, or other volatile agents to clean the printer exterior. Doing so can damage the case. Troubleshooting Consult the troubleshooting tables below whenever you start to have problems with the printer or application. If you can't find the solution problem below, contact your original retailer or your nearest authorized CASIO service center. Symptom Possible Cause Recommended Action Nothing The display contrast Adjust the display contrast appears on setting needs setting. (page 55) the display adjustment. when I The AC adaptor is not Make sure the AC adaptor is press . connected properly. properly connected. (Startup Guide, page 7) Battery power is low or Change to AC adaptor po...
Este manual também é adequado para os modelos :Impressoras - CW-L300 (873.99 kb)