Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Next, step onto the other pedal. Push the pedals until they begin to move with a continuous motion. Note: The pedal disks can turn in either direction. It is recommended that you turn the pedal disks in the direction shown below; however, for variety, you can turn the pedal disks in the opposite direction. To dismount the elliptical exerciser, allow the pedals to come to a complete stop. CAUTION: The elliptical exerciser does not have a freewheel; the pedals will continue to move until the flywheel stops. When the pedals are stationary, step off the highest pedal first. Then, step off the lowest pedal. Pedal Pedal Disk Upper Body Arm Upper Body Arm Arm Knob Wheel Upright Leveling Foot DIAGRAM OF THE CONSOLE Fan Button Increase Button Program Button Program Indicator Display Pace Guide Decrease Button Program Profiles FEATURES OF THE CONSOLE The advanced console offers a selection of features designed to make your workouts more effective. When you select the manual mode of the console, you can change the resistance of the pedals with the touch of a button. As you pedal, the console will provide continuous exercise feedback. You can even measure your heart rate using the built-in handgrip pulse sensor. In addition, the console features six preset programs. Each program automatically changes the resistance of the pedals and prompts you to vary your pedaling pace as it guides you through an effective workout. The console also offers two custom programs that allow you to create your own workout programs and store them in memory for future use. To use the manual mode of the console, see the instructions at the right. To use a preset program, see page 12. To create a custom program, see page 13. To use a custom program, see page 14. Before using the console, make sure that batteries are installed (see assembly step 8 on page 8). If there is a sheet of clear plastic on the display, remove the plastic. HOW TO USE THE MANUAL MODE 1 Turn on the console. To turn on the console, press the Increase or Decrease button or begin pedaling. The pace guide will light for a moment; the console will then be ready for use. 2 Select the manual mode. When you turn on the console, the manual mode will be selected. If you have selected a program, reselect the manual mode by pressing the Program button repeatedly until no program indicators (see the drawing above) appear along the left side of the display. 3 Change the resistance of the pedals as desired. As you pedal, change the resistance of the pedals by pressing the Increase and Decrease buttons. There are twelve resistance levels. Note: After you press the buttons, it will take a moment for the pedals to reach the selected resistance level. 11 12 Follow your progress with the display. The upper half of the display will show the elapsed time, the distance (in total revolutions) you have pedaled, and the resistance level of the pedals. The display will change modes every few seconds. Note: When a preset program is selected, the display will show the time remaining in the program instead of the elapsed time. The lower half of the display will show your pedaling speed, in revolutions per minute (RPM), and the approximate number of calories you have burned. The display will change modes every few seconds. The lower half of the display will also show your heart rate when you use the handgrip pulse sensor (see step 5). Measure your heart rate if desired. If there are sheets of clear plastic on the metal contacts on the handgrip pulse sensor, remove the plastic. Next, hold the handgrip pulse sensor with your palms resting on the contacts. When your pulse is detected, the heart-shaped indicator in the lower half of the display will flash each time your heart beats, and then your heart rate will appear in the display. For the most accurate heart rate reading, continue to hold the handgrip pulse sensor for about 30 seconds. Note: If you continue to hold the handgrip pulse sensor, the display will show your heart rate for about 30 seconds. The display will then show your heart rate along with the other modes. If your heart rate does not appear, make sure that your hands are positioned as described. Avoid moving your hands excessively or squeezing the metal contacts too tightly. For optimal performance, periodically clean the metal contacts using a soft cloth; never use alcohol, abrasives, or chemicals to clean the contacts. Turn on the fan if desired. To turn on the fan at low speed, press the Fan button. To turn on the fan at high speed, press the Fan button a second time. To turn off the fan, press the Fan button a third time. Note: If the fan is turned on but the pedals do not move for thirty seconds, the fan will automatically turn off to conserve the batteries. Rotate the thumb tab on the right side of the fan to adjust the angle of the fan. When you are finished exercising, the console will turn off automatically. If the pedals do not move for a few seconds, the time will begin to flas...