Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Before reading further, please review the drawing below and familiarize yourself with the labeled parts. Handrail Console Latch Knob Pulse Sensor Book Holder Key/Clip On/Off Circuit Breaker Walking Belt Cushioned Walking Platform Front Wheel Foot Rail Power Cord Rear Roller Adjustment Bolts Water Bottle Holder (Bottle not included) RIGHT SIDE LEFT SIDE 5 ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench and your own phillips screwdriver , adjustable wrench , and rubber mallet . Use the PART IDENTIFICATION CHART in the center of this manual to identify small parts as you assemble the treadmill. The assembly hardware is found into separate bags; each bag is marked to show which assembly step uses the hardware in that bag. Note: Some bags may include extra hardware. 2. Identify the Right and Left Uprights (55, 64); the Left Upright has two small holes near the square post. See drawing 2a. Make sure that there are two U-nuts (100) in the lower end of each Upright. Hold the Right Upright (55) near the Base (116), and orient the Right Upright as shown. Make sure that the Right Upright bends in the direction shown. Straighten the Wire Harness (49), and feed it into the lower end of the Right Upright and out of the upper end. Make sure that no wires are pinched. Hand tighten two Upright Bolts (112) with Star Washers (111) into the bottom of the Base (116) and the lower end of the Right Upright. Attach the Left Upright (64) as described above. Note: There is not a wire harness on the left side. 2 1. Read the information at the top of this page before beginning. Do not plug in the power cord until all assembly steps are completed. With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (51) so that the treadmill will be more stable. Do not fully fold the treadmill until it is completely assembled. Attach six Base Pads (44) to the bottom of the Base (116) with six 1” Tek Screws (13). Note: Only three Base Pads and Tek Screws are shown. 13 13 44 51 44 116 111 64 Bend Holes 55 116 112 49 1 3 3. With the help of a second person, carefully tip the treadmill down so that the Uprights (55, 64 [not shown]) are vertical. Make sure that the end of the Wire Harness (49) does not fall into the Right Upright. Set the Console Base (38) on the Right Upright (55) as shown. Check the pins in the connector on the end of the Wire Harness (49) and make sure that they are straight. Connect the Wire Harness to the indicated connector on the back of the Console Base. Make sure to insert the connectors properly (see the inset drawing). The connectors should slide easily and snap into place. If the connectors do not slide easily and snap into place, turn a connector and try again. 38 49 55 6 49 2a 100 55, 64 5. Tighten a 1/2” Tek Screw (113) into the right side of the 5 Crossbar (46) and the Right Upright (55). Attach the Console Base (38) to the Uprights (55, 64) with four 1/2” Screws (33). Make sure that the Wire Harness (49) is not pinched. 38 6. Tighten the 1/2” Tek Screw (113) in the left side of the Crossbar (46). Orient one of the Handgrip Extensions (34) so the bottom is open as shown, and insert it as far as possible into the post on the left Upright (64). If necessary, tap the Handgrip Extension with a rubber mallet to fully insert it. Attach the Handgrip Extension with two 3/4” Tek Screws (35), one towards the front of the post and the other towards the back. Attach the other Handgrip Extension to the post on the Right Upright (not shown) in the same way. 34 35 113 46 64 35 Post 6 49 55 33 64 113 46 33 7 7. See the inset drawing. Identify the Left Top Handgrip (31); there are identifying marks inside of the Handgrips. Set the Left Top Handgrip on the left Handgrip Extension (34). Insert two 1/2” Screws (33) into the two holes in the Handgrip Extension indicated by the arrows. Tighten the Screws into the Left Top Handgrip. Important: Do not tighten the Screws into the plastic bosses on the bottom of the Left Top Handgrip. 31 Bosses 64 33 34 7 31 43 4. Loosely thread a 1/2” Tek Screw (113) into the left side of 4 the Crossbar (46) and the Left Upright (64). Attach the Latch Assembly (32) to the Left Upright (64) with two 3/4” Tek Screws (35). 113 (Leave loose) 46 64 35 32 Open side 11.Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place; the allen wrench is used to adjust the walking belt (see page 25). Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubrican...