Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Keep your hands away from moving parts other than the designated handles. 6. When adjusting the seat, make sure the spring pin is fully engaged. If not, the seat may slip and cause serious injury. 7. Make certain all cables are seated within the pulleys before every use. 8. Exercise with care to avoid injury. 9. If unsure about the proper use of the BODYCRAFT STRATA strength training system call your local BODYCRAFT dealer or our customer service department at 800-990-5556. P PPARTS ARTSARTS LIST LISTLIST NO. DESCRIPTION QTY. 201 BASE CONNECTION 1 202 FRONT BASE 1 203 LEG PRESS SUPPORT 1 REAR TUBE SLIDING SEAT SUPPORT FRAME 1 2 204 205 206 SEAT SUPPORT 1 207 SLIDING TUBE 1 208 FOOT REST 1 209 STEEL ROLLER 1 HANDLE BAR 1210 211 SINGLE PULLEY BRACKET 1 212 50 ID. SQUA. END CAP 4 213 50 SQUA. END CAP 15 214 RUBBER STOP 2 RUBBER BUMPER 1215 216 NON-SKID PAD 8 217 SPRING PIN 1 218 3/4" STEEL BUSHING 4 219 1/2" STEEL BUSHING 8 1/2" X 7" HEX HEAD BOLT 2220 221 1/2" X 3-1/2" HEX HEAD BOLT 2 222 1/2" X 3-1/8" HEX HEAD BOLT 2 223 3/8" X 3" HEX HEAD BOLT 4 3/8" X 2-1/2" HEX HEAD BOLT 3/8" X 2" HEX HEAD BOLT 2 3 224 225 226 3/8" X 1" HEX HEAD BOLT 2 227 3/8" X 3/4" HEX HEAD BOLT 2 228 5/16" X 1/2" SETSCREW 4 1/2" WASHER 3/8" WASHER(LARGE) 12 2 229 230 231 3/8" WASHER(SMALL) 18 232 1/2" NYLON NUT 6 233 3/8" NYLON NUT 9 234 LEG PRESS CABLE 1 HOOK 1235 236 PULLEY 3 237 SEAT 1 238 BACK PAD 1 239 1" X 130 HAND GRIP 2 OWNER'S MANUAL 1240 84A TOP CABLE (2890 mm) 1 P PP ARTS ARTSARTS CHART CHARTCHART LEG-PRESS CABLE (234) (2030 mm) STEEL ROLLER(209) 1" x 130 HAND GRIP(239) HOOK(235) SPRING PIN(217) 1/2" STEEL BUSHING(219) 3/4" STEEL BUSHING(218) PULLEY(236) RUBBER STOP(214) BASE CONNECTION(201) FRONT BASE(202) LEG PRESS SUPPORT(203) SINGLE PULLEY BRACKET(211) REAR TUBE(204) SLIDING SEAT SUPPORT FRAME(205) SEAT SUPPORT(206) SLIDING TUBE(207) FOOT REST(208) SEAT(237) BACK PAD(238) HANDLE BAR(210) TOP CABLE(84A) (2890 mm) 1/2" X 3-1/2" HEX HEAD BOLT(221) 3/8" X 2-1/2" HEX HEAD BOLT(224) 0" 1" 2" 3" 4" 5" 6"1/2" 1-1/2" 2-1/2" 3-1/2" 4-1/2" 5-1/2" 7"6-1/2" 5/16" X 1/2" SETSCREW(228) 1/2" WASHER(229) 3/8" WASHER(SMALL)(231) 1/2" NYLON NUT(233) 3/8" NYLON NUT(234) 3/8" WASHER(LARGE)(230) FASTENER 2 3 STEP1 1.Attach BASE CONNECTION(201) and FRONT BASE(202) to the holes in the LEFT WEIGHT BASE of Bodycraft Strata home gym using two 1/2" x 3-1/8" HEX HEAD BOLT(222), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232). 2.Attach LEG PRESS SUPPORT(203) to FRONT BASE(202) using two 3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON NUT(232). Attach REAR TUBE(204) to LEG PRESS SUPPORT(203) as shown using two 3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON NUT(232). 213 201 201 203 202 204 LEFT WEIGHT BASE LEFT WEIGHT BASE 222 229 233 233 233 232 232 229 212 212 212 231 231 231 231 223 223 223 231 212 213 213 4 STEP2 Attach SLIDING SEAT SUPPORT FRAME(205) to LEG PRESS SUPPORT(203) as shown using two STEEL ROLLER(209) as shown. Attach SEAT SUPPORT(206) to SLIDING SEAT SUPPORT FRAME(205) as shown using two 1/2" x 3-1/2" HEX HEAD BOLT(221), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232) Tighten 5/16" X 1/2" SETSCREWS(228) with Hex Wrench to bolt STEEL ROLLERS (209) in place.(See FIG B) 213 213 218 218 218 218 219 219 205 213 216 208 220 229 229 229 229 232 229 229 221 221 229 232 232 208 205 206 203 209 Attach eight NON-SKID PAD(216) to FOOT REST(208). To ensure best performance, lubricate all pivot points during assembly. Attach FOOT REST(208) to SLIDING SEAT SUPPORT FRAME(205) as shown using two 1/2" x 7" HEX HEAD BOLT(220), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232). Insert two 3/4" STEEL BUSHING(218) and four 1/2" STEEL BUSHING(219) to SLIDING SEAT SUPPORT FRAME(205). 213 213 217 227 227 214 230 230 207 206 214 FIG A 205 203 209 228 228 FIG B STEP3 Attach HANDLE BAR(210) and SEAT(237) to SEAT SUPPORT(206) as shown using two 3/8" X 1" HEX HEAD BOLT(226) and two 3/8" WASHER(231). Attach BACK PAD(238) on SEAT SUPPORT(206) as shown using two 3/8" x 2-1/2" HEX HEAD BOLT(224) and two WASHER(SMALL)(231). CHECK that all the parts places. tighten all bolts. Attach alare l plin assembled correctly as astic ends caps and grips to drawing then appropriate 239 210 239 238 237 231 224 206 210 226 226 231 5 LEG PRESS CABLE LEG PRESS CABLE(234) If previously installed, completely remove TOP CABLE(84), along with pulleys T1, T2, T3, T4 and T5. Remove the two bolts and attach the TOP BEAM into the FRONT UPRIGHT. Assemble TOP CABLE(84A) (from leg press box) and pulleys simultaneously. Insert threaded end of TOP CABLE(84A) into slot in front of TOP BEAM, over pulleys T1, T2, around pulley T3, and over T4. Run threaded end of TOP CABLE(84A) through SINGLE PULLEY BRACKET(211) and attach pulley G1 as shown. Finish by routing TOP CABLE(84A) over pulley T5 and attach threaded end of TOP CABLE(84A) into SELECTOR ROD. For safety reasons, the threaded end should be screwed in using at least half of the av...