Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
a chair and you can see under the cycle easily. Adjust the resistance to maximum by turning the resistance adjustment knob to its extreme clockwise position. Check that the limiter screw (hex screw) of the brake caliper lever has not moved. If the brake caliper lever does not touch the limiter screw with the resistance at maximum, turn the adjustment nuts of the resistance adjustment wire until the lever touches the limiter screw. Lift the cycle back to the upright position. If the resistance still seems too small, proceed as follows: Loosen the fastening screw of the grey top cover and the seven screws of the white side covers and remove the side covers. Adjust the resistance to maximum by turning the resistance adjustment knob to its extreme clockwise position. Lean the cycle on its side so that it rests against e.g a chair and you can easily reach the control mechanism of the resistance adjustment wire under the frame. N.B. Take your watch off before the following step, as it may be damaged by the magnetic field of the brake mechanism. Push the approximately 1 mm thick plastic calibration strip between the magnetic caliper and the flywheel. If the brake caliper magnets are clearly further than 1 mm away from the flywheel rim, first open the locking nuts of the limiter screw and move the limiter screw slightly by turning the screw while holding the nuts at the same time (Fig. 6). Retighten the locking nuts of the limiter screw. Turn the adjustment nuts of the resistance adjustment wire, so that the magnet caliper is just in contact with the plastic strip with the resistance at maximum. N.B. Make sure you do not make the adjustment nuts too tight. Remove the calibration strip, lift the cycle into the upright position and replace the side and top covers. CHANGING BATTERIES If the meter display fades considerably or completely, change the batteries. Pull the meter out and remove the old batteries from the holder at the back of the meter. Push the new batteries into the holder (2 x 1.5 V AA) and push the meter back into its place at the top of the handlebar support tube. If you notice a malfunction during use, contact the dealer. Always give the serial number of your device! In spite of continuous quality control, individual defects and malfunctions may occur due to individual components. It is in most cases unnecessary to take the whole device for repair, as it is usually sufficient to replace the defective part. TRANSPORT AND STORAGE Move the cycle according to the following instruction: stand behind the cycle, grip the seat with one hand and the handle-bar with the other. Lift the cycle so that it rests on the transportation wheels and move it by wheeling. Lower the cycle onto the floor while holding on to the handlebar and remaining all the time behind the cycle. To prevent malfunctioning of the cycle, store in a dry place with as little temperature variation as possible, protected against dust. DIMENSIONS Length 96 cm Height 111 cm Width 62 cm Weight 41 kg All TUNTURI models are designed to meet the electromagnetic compatibility directive, EMC and are affixed with the CE conformity marking. Due to our continuous programme of product development we reserve the right to change specifications without notice. 5 1 2 3 4 106 109 5 11 10 6 7 8 9 32 33 111 34 39 44 31 30 47 12 13 11 14a 15 14b 16 17 107 48 49 50 51 52 108 53 86 87 88 89 83 84 85 18 19 20a 21 23 24 25 55 14d 67 65 114 66 112 29 30 31 90 91 92 93 113 20c 96 97 31 98 99 26 27 14c 28 18 146 20b 110 63 59 60 61 62 83 115 100 101 104 103 102 117 118 119 45 40 94 116 95 67 64 75 95 68 69 70 67 71 72 73 74 82 75 76 77 78 79 57 22 39 List for recycling / Index fur Materialentsorgung: A = Plastic, thermoplast Kunststoff, Thermoplast B = Paper, Carton Papier, Pappe C = Metal / Metall D = Electronics / Elektronik E = Batteries / Batterien F = Other / Sonstiges This list will help you to sort out the different components for recycling purposes. Dieser Index soll Ihnen die Zuordnung der Rohstoffe bei einer spateren Entsorgung erleichtern. 1 213 1001 (incl. 2) A 2 533 240 87 A 3 203 1012 (incl. 1, 7) C 4 233 1017 A/D (incl. 106, 109) 5 533 1019 A 6 72 0816 210 C 7 513 204 82 C 8 72 1015 90 C 9 60 08 075 40 C 10 173 1014 A 11 653 7020 C 12 60 48 016 57 C 13 653 5003 C 14 423 1044 F (incl. 14a - 14d) 15 203 1008 C 16 533 1017 A 17 173 1008 A 18 60 05 020 32 C 19 62 0612 16 C 20 403 1030 D (incl. 20a - 20c) 20c 407 1017 C 21 103 1014 C 22 533 1006 A 23 173 1007 L A - 173 1006 R A 24 653 264 87 C 25 651 206 80 C 26 60 42 016 59 C Ref.no Part no 27 653 133 84 A 28 652 852 81 C 29* 533 209 89 A 30* 60 10 025 03 C 31* 62 1022 25 C 32 443 1006 A 33 173 1012 (incl. 32,111) A 34 533 1018 A 39 153 1010 C 40 153 1009 A 44 653 1011 C 45 62 0412 10 C 47 153 1004 A 48 653 1018 C 49 60 06 016 03 C 50 153 1007 C 51 423 1053 F 52 533 0008 A/C 53 533 5002 A 54 62 0817 10 C 55 533 1035 A 57 533 1036 A 59 353 1010 A/C (incl. 60, 61) 60 353 1004 1 L C - 353 1005 1 R C 61 653 0002 A...