Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your LIFE FITNESS customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local LIFE FITNESS STRENGTH distributor or call the LIFE FITNESS STRENGTH customer service department at (800) 328-9714. 5. Consult your physician before beginning any exercise program. Tools Required for Assembly * Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * 5/16” Allen wrench, * Adjustable wrench * Tape measure 2 PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6788503 TOWER 2 22 3108002 WEIGHT STACK CUSHION4 2 6744102 NOVATRAK SWIVEL 2 23 6382301 PLATE BUSHING (10 CT.) 8 3 6789002 CENTER PULLEY BRACKET 2 24 3103801 5/16” SNAP HOOK 2 4 6744803 TOWER BRACE 2 25 6412001 3/8” SPRING PIN ASSEMBLY 2 5 6789102 SWIVEL HOLDER 2 26 3102501 3/8" FLAT WASHER 2 6 6789403 LOWER PULLEY HOUSING 2 27 3102502 1/2" FLAT WASHER 12 7 6789703 SWIVEL UPRIGHT 2 28 3102802 3/8” LOCK NUT 16 8 6788203 UPPER PULLEY HOUSING 2 29 3102801 1/2" LOCK NUT 18 9 6788103 CHIN-UP SUPPORT 1 30 3102804 1/2" LOW HT LOCK NUT 6 10 6459401 81” GUIDE ROD 4 31 3202401 3/8 X 1” BTN HD CAP SCREW 8 11 6785602 SHROUD 2 32 3102901 3/8 X 1-1/4" BOLT 2 12 3202402 1/2 X 3/4” BTN HD CAP SCREW 2 33 3102933 3/8 X 2" BOLT 6 13 3116101 4-1/2” PULLEY 14 34 3102922 3/8 X 2-3/4” BOLT 10 14 3116201 3-1/2” PULLEY 2 35 3202101 1/2 X 1-1/4" BOLT 8 15 6793201 STRAP 2 36 3102918 1/2 X 3-1/4” BOLT 6 16 6284501 WEIGHT STACK SHAFT 2 37 3202103 1/2 X 4” BOLT 10 17 6714601 HEAD PLATE 2 38 3102944 1/2 X 5” BOLT 2 18 6790101 CABLE2 39 6703801 WEIGHT STACK LABEL (LBS.) 2 19 6020601 1/2” FLANGE BEARING 4 40 6189501 WEIGHT STACK LABEL (1-25) 2 20 6480301 3/8” FLANGE SPACER 20 41 6214501 WEIGHT PLATE 40 21 6214401 WEIGHT STACK PIN 2 42 3103302 13/16” SHAFT COLLAR 4 Bolt Length Ruler NOTE: Bolt length is measured from the underside of the head of the bolt. BOLT LENGTH RULER: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 BOLT LENGTH 3 4 STEP 1 FIGURE 1 • LOOSELY assemble the two LOWER PULLEY HOUSINGS (6) to the two TOWERS (1) using four 1/2 X 4” BOLTS (37) and four 1/2” LOCK NUTS (29) as shown in FIGURE 1. 1 6 29 1 6 29 37 1/2 X 4” 1/2 X 4” 37 5 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 2 FIGURE 2 • LOOSELY assemble the two UPPER PULLEY HOUSINGS (8) to the two TOWERS (1) using two 1/2 X 3-1/4” BOLTS (36) and two 1/2” LOCK NUTS (29) as shown in FIGURE 2. 1 8 1 36 29 8 29 1/2 X 3-1/4” 36 1/2 X 3-1/4” 6 STEP 3 FIGURE 3 • SECURELY assemble two 3-1/2” PULLEYS (14) to the two NOVATRAK SWIVELS (2) using two 3/8 X 2” BOLTS (33) and two 3/8” LOCK NUTS (28). See FIGURE 3. 14 2 25 19 5 28 29 1/2 X 4” 37 3/8 X 2” 33 3/8 X 2” 33 2 1/2 X 4” 37 5 29 19 25 28 14 • Insert two 1/2” FLANGE BEARINGS (19) into each end of the NOVATRAK SWIVELS (2) and assemble them to the SWIVEL HOLDERS (5) using two 1/2 X 4” BOLTS (37), and two 1/2” LOCK NUTS (29). (NOTE: Tighten connection enough to remove play, yet allowing the SWIVEL HOLDER (2) to rotate freely.) See FIGURE 3. • SECURELY assemble two 3/8” SPRING PIN ASSEMBLIES (25) to the SWIVEL HOLDERS (5). See FIGURE 3. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 7 STEP 4 FIGURE 4 • LOOSELY assemble the two SWIVEL UPRIGHTS (7) to the LOWER PULLEY HOUSING (6) using four 1/2 X 3-1/4” BOLTS (36), four 1/2” WASHERS (27), and four 1/2” LOCK NUTS (29) as shown in FIGURE 4. 36 1/2 X 3-1/4” • Pull back the SPRING PINS on the SWIVEL HOLDERS (5) and slide assemblies over the SWIVEL UPRIGHTS (7) as shown in FIGURE 4. 7 29 29 27 7 5 5 6 6 • LOOSELY assemble the SWIVEL UPRIGHTS (7) to the UPPER PULLEY HOUSING (8) using two 1/2 X 5” BOLTS (38), four 1/2” WASHERS (27), and two 1/ 2” LOCK NUTS (29) as shown in FIGURE 4. 38 1/2 X 5” 29 8 27 29 8 38 1/2 X 5” 27 36 1/2 X 3-1/4” 27 • SECURELY assemble all loose connections made to this point. 8 STEP 5 FIGURE 5 9 1/2 X 1-1/4” 35 8 30 LOW HT. 7 • SECURELY assemble the CHIN-UP SUPPORT (9) to the two UPPER PULLEY HOUSINGS (8) using six 1/2 X 1-1/4” BOLTS (35) and six 1/2” LOW HEIGHT LOCK NUTS (30) as shown in FIGURE 5. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 9 FIGURE 6 • Loop the ball end of the CABLE (18) around one 4-1/ 2” PULLEY (13) and SECURELY assemble the 4-1/ 2” PULLEY (13) to the NOVATRAK SWIVEL (2) using one 3/8 X 2” BOLT (33) and one 3/8” LOCK NUT (28) as shown in FIGURE 6. • Route the threaded end of the CABLE (18) through the opening in the UPPER PULLEY HOUSING (8) and around two...