Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
DANGER: A risk of electrical shock may result from improper connection of the equipment-grounding conductor. Check with a qualified electrician if in doubt as to proper grounding technique. DO NOT modify the plug provided with the product. If it will not fit an electrical outlet, have a proper outlet installed by a qualified electrician. Any modification to the electrical plug will result in a voided warranty. Un branchement incorrect du conducteur de mise a la terre peut entrainer des risques de decharge electrique. Consulter un electricien si des doutes subsistent quant a la technique de mise a la terre. NE PAS MODIFIER la fiche fournie avec l'appareil. Si elle ne s'adapte pas a une prise, faire installer une prise correcte par un electricien qualifie. Toute modification a la fiche annule la garantie. HOW TO POSITION AND STABILIZE THE LIFE FITNESS TREADMILL Following all safety instructions in Section 1.1 and move the treadmill to the location in which it will be used. See Section 7 for the dimensions of the product footprint (assembled dimensions). SAFETY CLEARANCES The following information is supplied as regional reference data regarding safety clearances around the exterior of the treadmill. • EU: The European EN957 Safety Standard requires a 2 meter (6.5 feet) minimum from the rear of the treadmill to any object or surface. • U.S. and other regions: The ASTM International (ASTM ) F2115 - 05 Standard recommends the minimum dimensions to be 0.5 meter (1.64 feet) on each side of the treadmill and 1 meter (3.28 feet) behind the rearward most portion of the usable moving surface or 2 meters (6.5 feet) behind the furthest rearward obstruction to emergency egress from the treadmill. After placing the unit where it will be used, check its stability. If there is even a slight rocking motion or the unit is not stable, determine which stabilizing leg is not resting on the floor. To adjust, loosen the JAM NUT (A), and turn the STABILIZING LEG (B) until the rocking motion ceases, and both stabilizing legs rest firmly on the floor. Retighten the JAM NUT. Note: It is extremely important that the stabilizing leg be correctly adjusted for proper operation. An unbalanced unit may cause striding belt misalignment. A bubble level is recommended to ensure proper leveling. POWER SWITCH Located on the front panel at the base of the treadmill, the ON/OFF switch has two positions: "I" (one) for ON and "0" (zero) for OFF. CENTERING THE BELT After installing and levelling the treadmill, check the belt to ensure that it is tracking properly. First, plug the power cord into an appropriate outlet. See Electrical Requirements at the beginning of this section for details. Then turn the treadmill ON. Have one person stand on the platforms on either side of the treadmill frame. Do not stand on the belt at this time. Press the QUICK START key, and increase the speed to 4.0 miles per hour (mph), or 6.4 kilometers per hour (kph), using the SPEED UP arrow. If the striding belt moves to the right while it is running, have a second person turn the right tension bolt a quarter-turn clockwise, and then turn the left tension bolt (C) a quarter-turn counter-clockwise. See the illustration. This action sets the striding belt tracking back to center of the roller. If the striding belt moves to the left, turn the left tension bolt a quarter-turn clockwise and then turn the right tension bolt a quarter-turn counter-clockwise to start the striding belt tracking back to center of roller. Repeat these adjustments until striding belt appears centered. Allow the belt to continue running for several minutes to be sure that the tracking is stabilized. Note: Do not exceed one full turn of the adjusting screws in either direction. If, after one full turn, the belt does not track properly, contact Customer Support Services. C SERVICE ACCESS PORT The two interchangeable type RJ45 networking ports (A) are located on the back of the display console. These network ports, located behind the display console rear access door, allow for console software updates. POWER CORD ROUTING The power cord can be run straight from the treadmill, shortened and exited out the user-front left side, or run under the frame using the power cord clips and exited out the user right-rear side of the treadmill. For efficient cord management, the following routing options are recommended: With the power cord unplugged, insert the clips in the appropriate holes. See the illustration below. Use Hole Pattern 1 or 2 to locate the clips and secure the power cord with the clips, taking up any slack between clips. Note: It may be necessary to tip the treadmill to route the power cord properly. To plug the power cord into an outlet in front of the treadmill, use Hole Pattern 1 for outlets located at the front of the machine. Note: To accommodate treadmill incline, at least two feet (24”) of power cord is required between the outlet and the last power cord clip for outlets in front of the treadm...