Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. [Tools Required for Assembly] * Rubber mallet or hammer * 3/4" wrench * 9/16" wrench * Ratchet with 3/4" and 9/16" sockets * 5/32" Allen wrench * Adjustable wrench * Tape measure [ Bolt Length Ruler ] NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 5 6 PARTS LIST PART # DESCRIPTION QTY KEY PART DESCRIPTION# 6686603 FRONT LEG 1 10 3102501 3/8" WASHER 6693902 PULLEY BRACKET 1 11 3102802 3/8" LOCKNUT 3 6694002 CABLE SWIVEL 1 12 3102801 1/2" LOCKNUT 4 6694203 BASE CONNECTION 1 13 3102924 3/8 X 1-3/4" BOLT 5 3116201 3-1/2" PULLEY 2 14 3102904 3/8 X 3" BOLT 6 6405201 2" SQ. END CAP 1 15 3102918 1/2 X 3-1/4" BOLT 7 6467001 PARABODY LOGO END CAP 2 16 6694301 112-3/4" CABLE ASSY 8 3108102 QUICK DISCONNECT LINK 1 17 6694401 82-1/2" CABLE ASSY 9 6140701 GLIDE 1 X 1" 2 NOTE: The LEG PRESS ATTACHTMENT (832101) must be assembled before connecting it to the PARABODY 400 HOME GYM STEP 1 . Slide two PAILABODYLOGO END CAPS (7) over the FRONTLEG (1) as shown in FIGURE QTY 4 5 2 3 2 2 1 1 STEP 2 . Slide one 2" SQ. END CAP (6) as shown in FIGURE2. into the BASE CONNECTION (4) FIGURE 2 STEP 3 . Attachtwo 1 X 1" GLIDES (9) (2) as shown in FIGURE tothetop of puLLEY BRACKET FIGURE 3 1/2X3’1/4" FIGURE 4 STEP 4 . Securely fasten the LEG (1) and the BASE CONNECTION to the 400 HOME GYMusing two 1/2 X 3-1/4" BOLTS FRONT (4) (15) and two 1/2" LOCKNUTS See FIGURE (12). FIGURE 5 STEP 5 . . Remove one existing 3-1/2" PULLEYand two SPACERS fromthe ADJUSTMENT 832 LEG PRESS TUBE onthe OPTIONby unfastening the 3/8 X 4-1/2" BOLT holding the pulley on. See FIGURE 5. (Note: Save 3-1/2" PULLEY,it will be used in later steps.) 3-1/2" ~PACER BOLT i I 1/2I 1/2 I 1/2 1/2I 3 I 4I 5 I I I I I i 4 STEP 6 . Attach CABLE SWIVEL (3) to the ADJUSTMENTTUBE on the 832 using the existing previously removed 3/8 X 4-1/2" BOLTS, WASHERS, 2" WHEELS AND NUT.(Note: Securely tighten, then back off 1/4 turn to allow the CABLESWIVEL& WHEELS rotate See FIGURE 6. to freely.) FIGURE 6 3/8 X 3" FIGURE STEP 7 . Securely fastenthe 832 LEG PRESS to the FRONT LEG (i) using two 3/8 X 3" BOLTS (14), four 3/8" WASHERS(10), and 3/8" LOCKNUTS(11) as shown in FIGURE FIGURE 8 REMOVE STEP 8 Remove the existing LAT CABLE (part #668701) using the following steps: . Discolmect LAT BAR from TOP BOOM. . Unscrew the threaded end of CABLEfrom the HEADPLATE ASSEMBLY. . Route the LAT CABLE around the PULLEYBLOCKas shown in FIGURE 8. . Route the LAT CABLE around the TOP BOOM as shown in FIGURE 8. . The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE. [ 0 1/2 [ 1 1/2 I 2 1/2 I 3 1/2 [ 4 1/2 [ 5 1/2 I 6 FIGURE 9 Cablemustrunover the top of bolts. STEP 9 Install the NEW 112-3/4" CABLE ASSY (16) using the following steps: . Route the CABLE(16) through the TOP BOOM as shown in FIGURE9. The pulleys in TOP BOOM may need to be temporarily removed to perform this step. (Note: Make sure the CABLEis running OVERthe BOLTSconnecting the FRONTUPRIGHT to the TOP BOOM. These may also have to be removed to perform this step.) , Route the CABLE(16) around the PULLEYBLOCKas shown in FIGURE . Route the CABLE back over one pulley in the TOP BOOM, BRACKET and over the (16) down through the PULLEY (2) second pulley in the TOP BOOM. FIGURE 10 Screw the threaded end of CABLE (16) into the HEAD PLATE ASSEMBLY. STEP 10 Loop CABLE (16) around one 3-1/2" PULLEY(5) in the PULLEY BRACKET(2) using on 3/8 X 1-3/4" BOLT (13) and 3/8" LOCKNUT as FIGURE 10. (11) shown in 3/8 X 1-3/4" FIGURE 11 IMPORTANT: Tighten QUICK DISCONNECT LINK SECURELY. STEP 11 . LINK Attach the hook end of 82-1/2" CABLE(17) to the CABLESWIVEL(3) with one QU]:CK DISCONNECT IMPORTANT: Tighten the QUICK DISCONNECT LINK (8) securely. . Route the 82-1/2" CABLE(17) under the WEIGHTSTACKas shown in FIGURE 11. I 1/2I 1/2 I1/2 I 1/2 [ ~[/2 I 1/2 [ 34 56 8 STEP 12 FIGURE 12 o Screw the threaded end of 82-1/2" CABLE (17) to the PULLEY BRACKET as FIGURE 12. (2) shown in 3/8X1-3/4" FIGURE 13 STEP 13 . Attach one 3-1/2" PULLEY to the FRONT PULLEY(5) to the BASE CONNECTION (5) LEG (1) and one 3-1/2" (4) using 3/8 X 1-3/4" BOLTS (13) and two 3/8" LOCKNUTS. Make sure (17) is running under PULLEYS.) (Note: CABLE 9 SPRING PIN ADJUSTMENT FIGURE 14 STEP 14 The 832 LEG PRESS is equipped with a springpin adjustment to acconunodate differen! sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin. To set the correct amo~mtof tension in the cables, adjust the 832 LEG PRESS into the last adjustment hole (so the LEG PRESS is spread apart) and remove the WEIGHTSTACKPIN. Thread the 112-3/4" CABLE(16) into the HEADPLATE ASSEMBLY until the PULLEY (2) is held against and the cable is slightly pulling up on the HEADPLATE. BRACKET...