Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Tighten the SCREWS securely. Align the guide rollers located on the underside of the SEAT ASSEMBLY (F) with the SEAT EXTRUSION (L). Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION. Slide the SEAT ASSEMBLY fully forward. Connect the WIRE (M) leading from the user left side of the SEAT ASSEMBLY to the JACK located at the left front of the SEAT EXTRUSION. Insert the WIRE (M) into the WIRE HARNESS (N) located next to the JACK. In the hole located on the user right side of the SEAT EXTRUSION (L), behind the SEAT ASSEMBLY (F), install one 40 mm BUTTON HEAD SCREW W/LOCKING COMPOUND (7), one 24 mm FLAT WASHER (8), one RUBBER BUMPER SLEEVE (9), one 1" RUBBER BUMPER (10) and one 18 mm FLAT WASHER (3) as shown. R3 Only: NOTE: NOTE: R3 Only: 4. NOTE: Locate the ACCESSORY TRAY (K). Secure the ACCESSORY TRAY to the HANDLEBAR ASSEMBLY using four 8 mm PHILLIPS SCREWS (6) as shown. Tighten the SCREWS securely. The WIRE (M), JACK and WIRE HARNESS (N) are located on the user left side of the unit. Items shown on the right for clarity. Mount the SEAT ADJUSTMENT LEVER (O) to the user right side of the SEAT ASSEMBLY (F) using two 12 mm PHILLIPS SCREWS W/LOCKING COMPOUND (11). Tighten the SCREWS securely. Be sure to mount the SEAT ADJUSTMENT LEVER (O) with the adjustment knob facing upward as shown. Locate the SEAT EXTRUSION ENDCAP (P). Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRUSION (Q) using two 12 mm PHILLIPS SCREWS (12). Secure the SEAT BACK PAD (Q) to the UPPER SEAT SUPPORT TUBES (R) using four 55 mm PHILLIPS SCREWS (4) and LOCK WASHERS (5). Tighten the SCREWS securely. Secure the SEAT BACK COVER (JJ) to the SEAT BACK PAD (Q) using four M8 x 1.0 PHILLIPS SCREWS (19). Tighten the SCREWS securely. A zip-tie has been included to keep the MONOCOLUMN COVER (T) from falling during assembly. Untape the WIRE TIE (V) attached to the front of the MONOCOLUMN (S). Carefully pull the CONSOLE WIRE (W) through the SIDE ACCESS HOLE (X) of the MONOCOLUMN. Feed the CONSOLE WIRE through the GROMMET (Y) as shown and insert the GROMMET into the SIDE ACCESS HOLE. Locate the MONOCOLUMN (S). Slide the MONOCOLUMN COVER (T) onto the MONOCOLUMN as shown. Slide the MONOCOLUMN COVER up to the FRONT HANDLEBAR POSTS (U). 1 D 2 A B C R1 & R3 Recumbent Bikes Hardware List 1. 6. 7. (R1 Only) Assembly Sequence Seat Assembly Rear Stabilizer 4. & 5. Monocolumn, Wiring, Cover & Console Pedals Water Bottle & Bracket 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 2. & 3. Item Qty Description R1 R3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2 10 5 8 8 0 1 1 1 1 2 4 2 5 2 4 8 4 0 2 10 5 8 8 4 1 1 1 1 2 2 2 5 2 4 8 4 4 50 mm Button Head Screw Button Head Screw - 18 mm O.D. 55 mm Phillips Screw Lock Washer - 12.2 mm O.D. 8 mm Phillips Screw 40 mm Button Head Screw with Locking Compound Flat Washer - 24 mm O.D. Rubber Bumper 12 mm Phillips Screw with Locking Compound Phillips Screw Hex Head Bolt Thick Flat Washer - 16 mm O.D. mm Hex Head Bolt Small Head Phillips Screw Flat Washer - 12 mm O.D. 12 mm Self Tapping Screw 12mm Phillips Screw 15 mm Flat Washer Rubber Bumper Insert 1” 12 mm Large Head 100 mm 60 12 mm 1) 2) 4) 5) 7) 13) 14) 15) 16) 17) 18) 8) 9) 10) 11) 12) 3) Slide the MONOCOLUMN (S) into the MONOCOLUMN BRACKET (Z). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 100 mm HEX HEAD BOLTS (13) and three THICK FLAT WASHERS (14) (as shown) from the front side of the MONOCOLUMN and two 60 mm HEX HEAD BOLTS (15) and THICK FLAT WASHERS (14) from the user left side of the MONOCOLUMN BRACKET. Tighten the BOLTS securely. Be careful not to pinch the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) when inserting the MONOCOLUMN (S) into the MONOCOLUMN BRACKET. Connect the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) to the corresponding WIRE (W) from the SIDE ACCESS HOLE (X) of the MONOCOLUMN. Slide the MONOCOLUMN COVER (T) downward to meet the MAIN SHROUDS. Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 12 mm PHILLIPS SCREWS (16). Tighten the SCREWS securely. Do not overtighten the SCREWS. Attach the RIGHT (BB) and LEFT (CC) FRONT HANDLEBARS (labe...
Este manual também é adequado para os modelos :Formadores - LIFECYCLE R3 (3.98 mb)