Assessments - , GPA:
(
)
)
Fabricante : Life Fitness
Arquivo Tamanho: 1.1 mb
Arquivo Nome : f27a5464-c005-45cd-8877-ed739c8f6122.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
2.2 PREVENTIVE MAINTENANCE SCHEDULE Follow the schedule below to ensure proper operation of the product. ITEM WEEKLY MONTHLY QUARTERLY BI-ANNUAL ANNUAL DISPLAY CONSOLE / ACTIVITY ZONE ASSEMBLY Hardware Inspect Console and Clean Inspect Activity Zone Overlay iPod Connector/Cable Clean/Inspect USB Port Inspect Accessory Cups Clean Inspect Emergency Switch/Magnet Clean/Inspect HANDLEBAR ASSEMBLY Hardware Inspect ErgoTM Front Handlebar Clean Inspect Side Hand Rails Clean Inspect Lifepulse Sensors Clean/Inspect FRAME ASSEMBLY Hardware Inspect Motor Cover Clean Motor Electronic Compartment Vacuum Clean Inspect Drive Belt Inspect Leg Levelers Inspect/Adjust Front Roller Inspect Rear Roller Inspect Side Step Area Clean Inspect GENERAL Machine Level *Inspect Striding Belt Centered Inspect Frame, Toe Guards, Endcaps Visual Inspect *Use leveler to inspect 2.3 TROUBLESHOOTING THE TREADMILL Malfunction Probable Cause Corrective Action No Power On/Off switch. Turn the switch to the ON position. Insufficient power source. Plug treadmill into a dedicated 20 amp circuit. Refer to the Operations Manual. Using a voltmeter, verify power at outlet. If no power exists, reset circuit breaker at panel. Damaged line cord. Replace line cord. Contact Life Fitness Customer Support Services*. Line cord improperly seated in socket. Inspect power connection at wall outlet and at machine for proper contact. * See Section 2.7, How to Obtain Product Service, for contact information. TROUBLESHOOTING THE TREADMILL (CONTINUED) Malfunction Probable Cause Corrective Action Striding Belt slips off-center Uneven floor surface. Check levelers and level treadmill. Check striding belt & re-tension as necessary. Refer to Section 2.5 “How to Adjust and Tension the Striding Belt.” Maximum speed is reduced User is pushing striding belt. This occurs when the runner is running faster than the striding belt will travel, with the result of the striding belt being pushed with the runner’s feet. Instruct users not to push striding belt in either direction. User is stalling striding belt. This will occur with heavier users at lower striding belt speeds. The striding belt will “stall” if the user is traveling slower than the striding belt speed. Striding belt/deck malfunction. The deck laminate worn through or the underside of striding belt glazed over (hard, glossy). Replace belt and deck. Insufficient power source. Plug treadmill into a dedicated 20 amp. circuit. Rubbing sound from underneath machine Foreign objects may be stuck underneath the machine. Inspect underneath striding belt and machine. Remove any debris or objects that may cause interference with the treadmill. Plug treadmill into a dedicated 20 amp circuit. Display does not illuminate when machine is powered on Insufficient power source. Check all electrical connections for proper attachment. Loose 10 pin connection at display console or DSP Motor Control Board. to wire. Contact Life Fitness Customer Support Services*. Loose 28 pin connector at display console. Contact Life Fitness Customer Support Services*. 10 pin to 10 pin under console bridge. Contact Life Fitness Customer Support Services*. * See Section 2.7, How to Obtain Product Service, for contact information. TROUBLESHOOTING THE TREADMILL (CONTINUED) Malfunction Probable Cause Corrective Action Unit resets randomly or pauses Insufficient power source. Plug treadmill into a dedicated 20 amp circuit. (U.S. only) Damaged ground prong on line cord. Replace line cord. Line cord improperly seated in electrical outlet. Inspect power connection at electrical outlet and at machine for proper contact. Emergency stop magnet not engaged. Re-engage the emergency stop magnet. Activity Zone membrane switch Contact Life Fitness Customer Support Services* Pinched main wire harness. Contact Life Fitness Customer Support Services*. Open ground path. Contact Life Fitness Customer Support Services*. Inspect Stride Sensor system. Contact Life Fitness Customer Support Services*. * See Section 2.7, How to Obtain Product Service, for contact information. 2.4 TROUBLESHOOTING THE LIFEPULSE SYSTEM SENSORS If the heart rate reading is erratic or missing, do the following: • Dry the hands if necessary to prevent slipping. • Apply hands to all four sensors, located at the front and back of the hand grips. • Grasp the sensors firmly. • Apply constant pressure around the sensors. 2.5 HOW TO ADJUST AND TENSION THE STRIDING BELT Do not move treadmill or place hands under treadmill while it is plugged into an electrical outlet! THE BELT TENSIONING BOLTS A 5/16-inch hex key wrench is required for this task. The Life Fitness Treadmill has access holes in the rear roller guards which allow access to the tensioning bolts. These tensioning bolts make it possible to adjust the tracking and centering of the striding belt (A) without removing the guards. NOTE: It is extremely important that the treadmill be correctly leveled prior to any tracking adjustments. An unstable unit may ...