Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
3. Move basketball system to desired location. 4. Carefully rotate basketball system upright. 5. Reattach ground restraint and check system for stability. HEIGHT ADJUSTMENT 54 TUFF STUFF® and associated trademarks with permission of Mattel, Inc. Huffy endorsed or authorized in any way or any of its affiliated or subsidiary companies. The NBA and individual NBA other forms of intellectual property, may not be used, in whole or in part, WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net. • Do not slide, climb, shake or play on base and/or pole. • After assembly is complete, fill system completely with water or sand and stake to the ground. Never leave system in an upright position without filling base with weight, as system may tip over causing injuries. • When adjusting height or moving system, keep hands and fingers away from moving parts. • Do not allow children to move or adjust system. • During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. • Surface beneath the base must be smooth and free of gravel or other sharp objects. Punctures cause leakage and could cause system to tip over. • Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration. • Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace pole immediately. • Check system before each use for proper ballast, loose hardware, excessive wear and signs corrosion and repair before use. • Check system before each use for instability. • Do not use system during windy and/or severe weather conditions; system may tip over. Place system in the storage position and/or in an area protected from the wind and free from personal property and/or overhead wires. • Never play on damaged equipment. • See instruction manual for proper installation and maintenance. • When moving system, use caution to keep mechanism from shifting. • Keep pole top covered with cap at all times. • Do not allow water in tank to freeze. During sub-freezing weather add non-toxic antifreeze, sand or empty tank completely and store. (Do not use salt.) • Use extreme caution if placing system on sloped surface. System may tip over more easily. 201241 2/99 In the U.S.:1-800-558-5234 and Toll-Free 1-800-558-for Canada: 1-800-284-for Europe: 00 800 555 (Sweden: 009 555 85234), for Australia: 1-800-333 Internet ENGLISH INSTRUCTIONS 16. Attach lower elevator tubes (40) and counter balance spring (41) to IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL backboard support brackets (35) using spacers (34), bolt (37), and nut (39) as shown. Starting with nuts (16) flush against bracket (35) secure rim (42) and bracket to backboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Do not use washers here on spring return style rim. NOTE: Mounting nuts and bolts supplied with rim hardware. Attach upper elevator tubes (43) to backboard support brackets (35) using spacers (34), bolt (37), and nut (39) as shown. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. Install upper elevator tubes (43) to triangle plates (45) as shown. Install handle assembly to lower elevator tubes (40) using bolt (37), spacers (44), and nut (39) as shown. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. lower hole of top pole section (4) as shown. While maintaining 21. Insert bolt (37) through left side upper elevator tube (43), then stretch alignment, bounce top pole section (4) and middle section (5) together spring (41) onto bolt (37). Insert bolt (37) through right side upper as shown until they no longer move toward taped reference mark. elevator tube (43) and secure with nut (39). Upright assembly. NOTE: Pole sections should have a 3-1/2” (9 cm) 22. Roll completed assembly to desired position. Fill tank with water overlap minimum. (approx. 28 gallons (106 Liters)) or sand (approx. 225 lbs. (102 kg)) and 5. IMPORTANT! Center alignment slot of lower pole section (6) in a snap cap (49) in place. Secure assembly to ground using rope (52) and lower hole of middle pole section (5) as in step 4. While maintaining tie down stake (53). alignment, bounce assembly and lower ...