Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
28 26 16 P/N 214953C 12/03 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HUFFYSPORTS TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) (2) 1/2”, (2) 9/16" AND (2) 3/4" Wrenches 9/16”1/2” AND/OR (2) Socket Wrenches and Sockets Item #21 Item #47 Item #48 Item #37 Item #38 Item #44 Item #55 Item #16 Item #50 Item #35 Item #39 Item #56 Item #203/4” 17 12/03 P/N 214953C Install spacers (36) onto backboard brackets (34) with bolts (37, 21) and lock-nuts (35, 20) as shown. 16. 36 20 35 21 34 37 Assemble lower elevator tubes (40) as shown. NOTE: Test fit bolts into holes of brackets (34) and carefully rock them in a circular 17. motion to ream out paint from holes if necessary 40 40 47 41 34 55 55 39 IMPORTANT!: Refer to instructions included with board and rim hardware for backboard and rim assembly. IMPORTANT!: It is necessary for all parts to be installed for this mechanism to work safely and properly. 18 P/N 214953C 12/03 Starting with nuts (16) flush against bracket (34), secure rim (42) and bracket to backboard. Bend bracket (34) to line up with holes in backboard and secure. 18. 19. IMPORTANT!: For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE A: Mounting nuts and bolts supplied with rim hardware. 34 16 42 16 Do not use washers here on spring return style rim. NOTE B: 56 19 12/03 P/N 214953C P/N 214953C 12/03 20 Assemble upper elevator tubes (43) to backboard brackets (34). SAWHORSE OR SUPPORT TABLE Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT!: DO NOT OVER TIGHTEN NOTE: STEP COMPLETED ASSEMBLY: 20. 39 47 55 55 43 43 34 39 48 40 46 40 40 4 45 45 47 38 38 44 44 21. Install upper elevator tubes (43) to triangle plates (45) as shown. 22. 47 39 44 44 28 Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: IMPORTANT!: DO NOT OVER TIGHTEN 40 47 38 40 39 43 38 45 43 23. 39 47 43 43 40 40 38 55 55 38 38 38 Install handle assembly (28) to lower elevator tubes (40) using bolt (47), spacers (38, 55), and nut (39) as shown. 21 12/03 P/N 214953C 41 39 47 43 43 24. USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). 53 49 52 Roll completed assembly to desired position. Secure assembly to ground using anchor strap (52) and tie down stake (53). Fill tank with water (approx. 30 gallons/115 Liters) or sand (approx. 255 lbs./113 kg) and snap cap (49) in place. DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. CAUTION! 25. 22 P/N 214953C 12/03 23 12/03 P/N 214953C 26 26. 27. 28. HUFFYHUFFYSPORTSSPORTS 54 10 ft. (3.05 m) While holding handle, remove pin (26). Move elevator up or down to desired height. Replace pin (26) full length to lock system at desired height. Apply height and transport label (54) to front of pole as shown. DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! Peel protective film from surface of acrylic backboard prior to use. NOTE: 26. 27. 28. 26 - 28. 29. Install net clips. Attachez les pinces de filet au cerceau, comme illustre. 30. Die Netzhalteklammern wie gezeigt am Korbrand anbringen. Instale los sujetadores de la red en el borde, como se muestra. 50 CLIP ARMS " BRAS " DE LA PINCE CLIP-ARM "BRAZO" DEL SUJETADOR CLIP BODY " CORPS " DE LA PINCE CLIP-HAUPTTEIL "CUERPO" DEL SUJETADOR WARNING! AVERTISSEMENT ! WARNUNG! .ADVERTENCIA! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. L'UTILISATION DE CE PRODUIT SANS L'INSTALLATION CORRECTE DES SMART CLIPS® OU EN L'ABSENCE DE CERTAINES SMART CLIPS® EXPOSE LES JOUEURS A DES BLESSURES. VEILLEZ A SUIVRE SCRUPULEUSEMENT CES INSTRUCTIONS. EIN GEBRAUCH DIESES PRODUKTS OHNE ORDNUNGSGEMASS ANGEBRACHTE SMART CLIPS® BZW. MIT FEHLENDEN SMART CLIPS® KANN VERLETZUNGEN NACH SICH ZIEHEN. DIE ANLEITUNG GENAU BEFOLGEN. EL USO DE ESTE PRODUCTO SIN LA INSTALACION ADECUADA DE LOS SUJETADORES SMART CLIP®, O LA FALTA DE ELLOS PUEDE DAR COMO RESULTADO DANOS CORPORALES. ASEGURESE DE SEGUIR CUIDADOSAMENTE LAS INSTRUCCIONES. AABBCC50 42 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm...