Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
x 1.19 Long 56 4* 203257 Zip Tie 57 1 203255 Front Cover * You may have extra parts with this model. P/N 211447 04/01 4 printed on recycled paper ENGLISH INSTRUCTIONS use washers here on spring return style rim. NOTE B: Mounting nuts and IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF bolts supplied with rim hardware. THIS OWNERS MANUAL 20. 1. Remove all contents from underside of tank. Keep tank (1) bottom side 21. up. 22. 2. Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 23. 3. Mark pole sections with tape as shown. 24. 4. IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce pole top (4) and middle section (5) together as shown 25. until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a 3-1/2” (9 cm) minimum overlap. 5. IMPORTANT! Center alignment slot of lower pole section (6) in a 26. lower hole of middle pole section (5) as in step 4. While maintaining alignment, bounce assembly and lower section (6) together as shown until they no longer move toward taped reference mark. NOTE: Pole 27. sections should have a 3-1/2” (9 cm) minimum overlap. 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7. Insert pole assembly into tank assembly as shown. 8. Carefully place unit on its side. Secure pole bottom (6) to tank as shown. Upright unit. NOTE: Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. IMPORTANT! Do not over tighten, will crack tank. 9. Secure strut tubes (11) to bottom pole section (6) as shown. 28. WARNING: TIGHTEN BOLT (14) IN LOCKNUT (12) UNTIL FLUSH (EVEN) WITH LOCKNUT’S OUTER EDGE. 29. 10. Once again, carefully place unit in the side position and secure strut (11) 30. to tank (1) as shown. Completely tighten. Repeat for opposite side. 31. Upright unit. NOTE: Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. 32. 11. Install pole mount (17) bracket with carriage bolts (18) as shown. Tighten 33. flange nuts (16) completely. 12. Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), and nuts (20) as shown. IMPORTANT! Tighten until 34. washers (19) no longer move. 13. Attach covers (24) onto pole mount bracket (17) with carriage bolt (25) and nut (16) as shown. IMPORTANT: Loop end of pin lanyard (27) over carriage bolt (25) during this assembly. NOTE: Assemble lanyard (27) to locking pin (26) as shown. 14. Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle parts (32, 33) to adjustment rod with screw (31), carriage bolt (30), and flange nut (16) as shown. IMPORTANT: Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. NOTE: Holes in adjustment rod allow for either rear access or side access. 15. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (26). 16. Install spacers (36) onto backboard brackets (34) with bolts (37, 21) and lock-nuts (35, 20) as shown. 17. Assemble lower elevator tubes (40) as shown. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. NOTE: Test fit bolts into holes of brackets (34) and carefully rock them in a circular motion to ream out paint from holes if necessary. 18. Install net clips (50) to rim (42). The Quick Clip™ rapid release net system lets the net pull away from the rim. This reduces the risk of player injury or property damage. However, improper installation or a ball making contact at an odd angle may disengage the net clip from the goal rim. Usually, the clip is reinstalled with little or no problem. We hope that you agree this inconvenience is minor when compared to the safety of the players. Quick Clip: US Patent No. 5,792,010/5,795,253 The two outer hooks on net clip must face towards inside of goal rim. Insert larger hole in net clip onto rim stud, push down on net clip, then slide net clip right, locking or snapping securely into position (clips must "snap" into place to insure a secure fit). NOTE: Net clips should not slide with ease. It is very important that the net clips are in the locked position before going on to next step. WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. 19. Starting with nuts (16) flush against bracket (34), secure rim (42) and bracket to backboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE A: Do not printed on recycled paper...