Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
10 14 20 7 1421 12 10 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING REAR VIEWIMPORTANT! Do not over tighten. 9 12/02 P/N 211446D Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18). 15. THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 19 17 20 14 7 14 18 REAR VIEW P/N 211446D 12/02 10 RIM ASSEMBLY & INSTALLATION WARNING 17. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. 42 41 27 Apply foam pad (22)behind bracket (39) and attach bracket (39) to backboard and support structure by inserting bolts (26) and washers (24) through top holes in bracket (39), Tighten nuts (23) completely. 26 39 24 23 2418. 23 24 24 40 26 Insert inner bracket (40) into bracket (39) as shown. Insert bolts (26) and washers (24) through top holes of inner bracket (40) as shown, Tighten nuts (23) completely. 19. 39 40 39 22 11 12/02 P/N 211446D 20. 20. Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (45) as shown.Tighten completely. 2539 40 BOTTOM VIEW 45 25 41 27 44 2727 45 42 21. Install rubber grommet (28), concave washer (29) and center lock nut (30) to carriage bolt (41) as shown. NOTE Do not over tighten as rim will not flex properly. See leveling instructions to determine how much to tighten nuts (42) and (30). 28 41 30 29 P/N 211446D 12/02 12 22. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing. 25 42 30 23. Apply logo label (33) to cover plate (31). Install cover plate (18) on rim (25) using self tapping screws (32) as shown. NOTE ORIENTATION OF COVER PLATE 31 33 32 24. Secure net (34) to rim (25). 1 2 3 34 25 OUTSIDE VIEW 4 10 feet (3.05 m) NOTE: Official rim height is 10’ (3.05 m) from top of rim to playing surface. 13 12/02 P/N 211446D 25. 25. Check leveling at this time. Pole should be level in all directions. NOTE: If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange. (Refered to in Step 6.) After system is leveled, completely tighten nuts (7) above pole flange. 26. Apply height adjustment label (37) to front of pole as shown. 10 feet (3.05 m) REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 37 P/N 211446D 12/02 14 ADDING HEIGHT INDICATORS Add height adjustment decal (35) 27. A. LOWER BACKBOARD UNTIL RIM IS 7 FEET OFF THE GROUND. B. APPLY THIN WHITE STRIP TO BOTTOM EDGE OF OUTER CRANK TUBE AS SHOWN. C. APPLY LARGE DECAL TO BACK OF POLE SO THAT 7 FOOT MARK ON LARGE DECAL IS LINED UP WITH THIN WHITE STRIP. B 15 12/02 P/N 211446D Rotate crank handle to raise and lower backboard. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. Refer to Step 10 and Step 14. 29. Secure pole pad (36) as shown.28. 36 Height Adjustment NOTE: Pole pad may NOT be included in this model. 29. Secure pole pad (36) as shown.28. 36 Height Adjustment NOTE: Pole pad may NOT be included in this model. P/N 211446D 12/02 16 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Qty. 4 12 1 8* 1 1 10* 8 2 2 2 3 1 24 2 4 1 1 1 1 1 1 4 Part No. Description 200573 J-Bolt, 5/8”-11” 265575 Nut, Hex 5/8”-11” 920880 Mounting Plate 203470 Washer, Flat 5/8” I.D. x 1.5” O.D. 980880 Pole 200544 Pole Cap, Square 206340 Nylon Insert Lock Nut, Hex 1/2”-13 220589 Cap, Arm Support Insert 916880 Support Arm, 42” Long, (Upper) 926880 Support Arm, 52” Long, (Lower) 220586 Logo Label, 15” x 1 3/4” 200574 Bolt, Hex Flange 1/2”-13 x 10” 906880 H-Frame Board Assembly 203474 Washer, Flat 1/2”x 1” O.D. 201640 Bolt, Hex, 1/2”-13 x 7.25” 202856 Bolt, Hex Head,1/2”-13 x 4” 900656 Bracket, Jack Support (Left) 900658 Bracket, Jack Support (Right) 206251 Bolt, Hex, 1/2”-13 x 5” 222880 Crank Jack 200576 Spacer, Zinc .75” x 6” 203274 Foam Pad 5x 5 203100 Nut, Hex Flange 5/16”-18 Item Qty. Part No. Description 24 8 203218 Washer, Flat 5/16” x 7/8” O.D. 25 1 920263 Rim, Orange 26 4 201611 Bolt, Hex Flange, 5/16”-18 x 3” 27 5* 203232 Washer, 3/4 O.D. 28 1 220041 Grommet, Rubber 29 1 220043 Washer, Large Concave 3...