Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
1 Remove contents from tank Remove contents from tank 2. Correctly identify each pole section and mark indicated distance from ends with tape (not supplied) as shown. TOP 4 TAPE (Not Supplied) MIDDLE 5 5” (13 cm) BOTTOM 6 5” (13 cm) 3. IMPORTANT! Center the alignment slot of middle pole section (5) in the lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle section of pole (5) into top section of pole (4) using wood scrap as shown until they no longer move toward taped reference mark. WOOD SCRAP (NOT SUPPLIED) 5 4 POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 9 10/03 P/N 211994C 4 5 6 WOOD SCRAP 4. IMPORTANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark. 6 5 POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4 5 6 WOOD SCRAP 4. IMPORTANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark. 6 5 POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 8 7 6 8 7 46 5 10 P/N 211994C 10/03 10 6 7 8 6. 28 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. IMPORTANT!: DO NOT OVER TIGHTEN THE SPACER (28) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 6. 28 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. IMPORTANT!: DO NOT OVER TIGHTEN THE SPACER (28) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 11 13 1 14 13 12 127. Secure tank struts (13) to pole. Rotate non-secured ends of tank struts (13) outward to mounting holes in tank as shown. TIGHTEN BOLT (11) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 11 10/03 P/N 211994C 8. 13 13 1 Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. 13 17 12 12 16 8. 13 13 1 Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. 13 17 12 12 16 12 P/N 211994C 10/03 SECTION B: ASSEMBLE THE BOARD AND RIM This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) 1/2” 1/2” AND/OR Item #19 (12) Item #17 (6) Item #21 (4) Item #22 (4) Item #23 (2) 13 10/03 P/N 211994C 1. 1. Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 3 of this section IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. 21 22 22 18 20 17 17 IMPORTANT!: Refer to instructions included with rim hardware for backboard and rim assembly. 14 P/N 211994C 10/03 2. SAWHORSE OR SUPPORT TABLE Support pole and tank assembly over support table. Carefully slide backboard components onto pole. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! 3. 26 24 23 While still in the horizontal position, carefully slide backboard components onto pole. Secure hardware at desired position as shown and tighten all hardware completely at this time. 4 15 10/03 P/N 211994C 4. Install clips. CLIP “ARM” CLIP “BODY” USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. WARNING! 19 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping. A AA B BB C CC 18 16 P/N 211994C 10/03 Insert net into bottom of clip as shown. SIDE VIEW Twis...