Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at 5 01/04 P/N 214955E Get to know the basic parts of your basketball system..... SUPPORT STRUT BACKBOARD FRONT RIM BASE POLE FRONT PANEL WHEELS 6 P/N 214955E 01/04 PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 1 206336 Tank 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4“ (Black) 4 1 904847 Top Pole Section 5 1 908024 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eyebolt, 3/8-16 x 3-3/4 Long 9 1 202821 Disk, 2-3/4 Diameter 10 1 203063 Nylon Insert Lock Nut, 3/8-16 11 2 906410 Strut, 43” Long, With Flat Ends 12 1 203220 Nut, Ny-lock, 5/16-18 13 7 203218 Washer, 5/16 Flat 14 1 201625 Bolt,Yellow Dichromate,5/16-18 X 3.60 Long 15 2 203798 Bolt, Hex Flange, 5/16-18 x 1-1/2 Long 16 9* 203100 Hex Flange Nut 5/16-18 17 1 204832 Bracket, Pole Mount 18 2 203231 Carriage Bolt, 5/16-18 x 3-1/2 Long 19 4 203232 Washer, Metal, 3/4” O.D. 20 4* 201124 Lock Nut, Hex Head, 3/8-16 21 4 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long 22 2 204858 Spacer, Biscuit, Plastic 23 2 204857 Spacer, Metal 1/2” O.D.x1.44 Long 24 2 204859 Cover, Spring 25 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long 26 1 204850 Pin, Locking 27 1 204853 Lanyard, Black Coil 28 1 904833 Height Adjustment Rod 29 1 204872 Label, Height Indicator 30 2 203103 Carriage Bolt, 5/16-18 x 2 Long Item Qty. Part No. Description 31 1 204803 Screw, Phillips Head 32 1 204855 Handle, Left 33 1 204856 Handle, Right 34 2 900964 Board Bracket 35 1 203255 Front Cover 36 2 200874 Spacer, Steel .402 I.D. x .50 O.D. x 1.5 Long 37 1 206990 Reinforcement Bracket 38 4 201681 Spacer, Plastic, .530 I.D. x .875 Long 39 7 206340 Lock Nut, Hex Head, 1/2-13 40 2 904808 Elevator Tube, Lower - Long 41 1 204837 Spring 42 1 Rim 43 2 904820 Elevator Tube, Upper - Short 44 2 201682 Spacer, .530 I.D. x 1.875 Long 45 2 900867 Plate, Triangle, (Black) 46 1 202814 Cap, Pole Top 47 6 206244 Bolt, Hex, 1/2-13 x 8 Long 48 1 204870 Bolt, Hex, 1/2-13 x 3-1/2 Long 49 2 203617 Plug Cap 50 12 201219 Smart Clip, Net Holder 51 1 Net 52 1 201568 Anchor, T-Strap 53 1 203124 Stake, Tie Down 54 1 201252 Label, Height Adjustment and Moving 55 4* 205528 Bolt, Hex Flange, 5/16-18 x 1 Long 56 4* 203257 Zip Tie 57 4 201683 Spacer, 530 I.D. x1.5 Long * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. HARDWARE IDENTIFIER (BOLTS & WASHERS) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) Item #10 (1) Item #12 (1) Item #13 (7) Item #16 (9)* Item #39 (7) Item #9 (1) Item #20 (4)* Item #19 (4) 7 01/04 P/N 214955E HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #8 (1) Item #15 (2) Item #18 (2) Item #25 (1) Item #30 (2) Item #31 (1) Item #47 (6) Item #55 (4)* Item #21 (4) Item #14 (1) Item #48 (1) * You may have extra parts with this model. 8 P/N 214955E 01/04 HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #2 (2) Item #36 (2) Item #7 (1) Item #23 (2) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #22 (2) Item #44 (2) Item #57 (4) Item #50 (12) Item #38 (4) 9 01/04 P/N 214955E Remove all contents from underside of tank. Keep tank (1) bottom side up 1. 1. 1 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 3 2 2. 1 4 5 Mark pole sections with tape as shown. TAPE (not included) 3. 6 10 P/N 214955E 01/04 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. 5 4 IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4. 01/04 P/N 214955E11 IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3. While maintaining alignment, bounce top & middle pole assembly (4 & 5) onto lower pole section (6) as shown until top & middle pole assembly no longer moves toward taped reference mark on bottom pole. 4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. 6. 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 8 6 5 Insert pole assembly into tank assembly as shown. 7. 6 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING...