Assessments - , GPA:
(
)
)
Fabricante : Huffy
Arquivo Tamanho: 747.52 kb
Arquivo Nome : d6fec7b0-1904-458f-9f69-e5a4c83c9577.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Upright 19. Install fiberglass rods (33) into pockets on net. Top and bottom ends of assembly. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum rods are inserted into holes on framework. Attach pole pad as shown. overlap. 20 Attach snap clips on tarp to “D” ring on net as shown. 4. IMPORTANT! Center alignment slot of lower pole section (6) in a Thread straps on net through tarp as shown and tighten straps to lower hole of middle pole section (5) as in step 4. While maintaining desired tarp tension. alignment, bounce assembly and lower section (6) together as shown until they no longer moved toward taped reference mark. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. 5. Install rod (7) through holes in bottom pole (6) section and eyebolt (8). 6. Install wheel axle (2) through wheel carriage (9) and install wheels (3) onto wheel axle (3) with spacers (28) as shown. Insert pole assembly into tank assembly as shown.Secure bottom pole (6) to tank, lower bracket “A” (36) and wheel bracket as shown, a deep socket is recommended. NOTE: Two people recommended for this step. IMPORTANT! DO NOT OVER TIGHTEN. 7. Secure tank struts (13) to pole. Rotate non-secured ends of tank struts (13) outward to mounting holes in tank as shown. WARNING: TIGHTEN BOLT (11) IN LOCK NUT (14) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. 8. Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. 9. Mount brackets (20), rim spacer (45) and rim (18) to backboard and finger tighten. NOTE: Final adjustments will be made in Step 12. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. 10. Support pole and tank assembly over support table. Carefully slide backboard components onto pole. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER. 11. While still in the horizontal position, secure hardware at desired position as shown and tighten all hardware completely at this time. 12. Install netclips and net as instructed on illustration page. 13. NOTE: Two people recommended for this procedure. Carefully upright assembly. Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER. WARRANTY CARD: 14. Place assembled unit to desired location. Fill tank with water (30 gallons Please remember to complete your product (114 liters)) or sand (360 lb. (163 kg)) and snap tank cap (30) in place. registration form either on-line at: Insert T-strap (29) through slot on back of base as shown. Secure unit to or mail-in ground by twisting tie down stake (27) into ground and hooking T-strap the enclosed postcard. (29) onto tie down stake (27). IMPORTANT! Add two gallons (7.6 liters) of non-toxic antifreeze in sub-freezing climates. 15. Slide framework halves into net and insert reduced end of frame into expanded end as shown. NOTE: TABS ON STRAPS SHOULD BE POSITIONED ON THE OUTSIDE 3 02/04 P/N 211583 PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description 1 1 206645 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 Top Pole Section 1 900166 Bottom Pole Section 6 1 900315 Middle Pole Section w/ Rivnut and Label 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eye Bolt, 3/8 x 16 x 3-3/4 Long 9 1 200924 Wheel Bracket 1 203063 Lock Nut, Nylon Insert, 3/8-16 11 1 202541 Bolt, Hex Head, 5/16-18 x 3-3/4 12 10 203218 Washer, 5/16 Flat 13 2 906206 Tank Strut 14 1 203220 Lock Nut, 5/16-18 1 200439 Label, Moving System and Height Adjust. 16 2 203156 Bolt, Hex Head, 5/16-18 x 1 Long 17 10 203100 Nut, Hex Flange 5/16-18 18 1 Rim 19 12* 201219 Clip, Net Holder 2 900162 Backboard Mounting Bracket 21 4 203309 Washer, 1 O.D. 22 4 203113 Bolt, Hex Flange, 5/16-18 x 2-1/2 Long 23 2 203231 Bolt, Carriage 5/16-18 x 3-1/2 24 2 203435 Knob, Plastic, 1-3/4 Diameter 1 Net 26 1 206219 Cap 27 1 203124 Tie Down Stake 28 2 201651 Spacer, Wheel Axle 29 1 200929 T-Strap 1 203617 Tank Cap 31 2 900314 Sportstation Frame (tapered end) 32 2 900313 Sportstation Frame 33 2 201554 Rod, Fiberglass 34 1 201549 Tarp, Soccer/Hockey 1 201548 Tarp, Football/Baseball 36 1 900316 Bracket, Lower ”A” 37 1 900317 Bracket, Lower ”B” 38 2 900311 Bracket, Upper 39 4 202739 Bolt, 5/16-18 x 1-3/4 Long 4 201552 End Cap, Square 41 1 201558 Knob, 2” 42 1 201559 Knob, 1” 43 1 201585 Storage Bag 44 1 201547 Net Assembly 1 203365 Rim Spacer * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 4 P/N 211583 02/04 4 8 7 65. Note (See Text Page) Note (See Text Page) 6. 2 28 283 3 9 10 6 7 RIVNUT FACES FRONT OF UNIT 36 8 4 8 7 65. Note (See Text Page) Note (See Te...