Assessments - , GPA:
(
)
)
Fabricante : Huffy
Arquivo Tamanho: 3.48 mb
Arquivo Nome : 0d8f1263-9682-6804-1d6d-87ceadb53b11.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Align dimple of top pole section (4) into trough of middle pole section (5) as shown. IMPORTANT! HOLE DIMPLE middle pole THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 11/ 2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5" middle pole 1-1/2" ID STICKER 14 ID# M661134 03/06 5. 5. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. IMPORTANT! HOLE DIMPLE Bottom pole THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5" 1-1/2" ID STICKER Bottom pole 15 03/06 ID# M661134 ID# M661134 03/06 16 12 53 10 51 51 6. Attach pole assembly to base (1) as shown. Secure pole assembly to tank using bolts (50) and pole mounting bracket (49) as shown. 7. Secure tank struts (2) to pole as shown. Place cover (53) over exposed end of bolt as shown. 6 49 49 6 1 2 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 50 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT TIGHTEN COMPLETELY IMPORTANT! 50 17 03/06 ID# M661134 7 18 8. Rotate non-secured ends of tank struts (2) outward to mounting holes in tank as shown. Secure ends of tank struts (2) to wheel bracket (7), as shown. Repeat for opposite side. 2 2 48 47 9. Secure cover (28) to tank struts (2) using bolts (47) and nuts (48) as shown. 28 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! TIGHTEN ALL COMPONENTS COMPLETELY (STEPS 7-9) IMPORTANT! DO NOT TIGHTEN COMPLETELY IMPORTANT! 51 18 51 ID# M661134 03/06 18 10. Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) as shown. Tighten flange nuts (14) completely. 4 42 16 16 15 14 14 11. Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (11) as shown. 15 17 17 11 19 17 17 21 20 20 21 IMPORTANT! Tighten just until washers (17) stop moving. Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 12. 12. 15 14 24 22 22 25 23 FIG. A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it passes through the pole mount bracket (15) during this assembly. IMPORTANT! 23 25 24 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (24). 24 13. 19 03/06 ID# M661134 ID# M661134 03/06 20 TOOLS REQUIRED FOR THIS SECTION SECTION B: ATTACH THE BACKBOARD Phillips-Head Screwdriver This is what your system will look like when you’ve finished this section. Wrenches: (2) 1/2", (2) 9/16”, and (2) 3/4” (2) Socket Wrenches and Sockets And/Or 1/2” 9/16” Extension 3/4” Sawhorse 35 32 Upper Elevator tube Lower Elevator tube Identify elevator tubes. TOWARDS BOARD TOWARDS POLE 1. 1. Assemble backboard brackets (27) using bolts (52), and nuts (11) as shown. 27 52 11 11 52 27 29 NOTE ORIENTATION 21 03/06 ID# M661134 ID# M661134 03/06 22 Support pole on sawhorse. Attach triangle plates (37) and elevator tubes (35 & 32) to top pole (4) using bolts (40 & 29) and nuts (31). Install pole cap (38). 2. 35 31 29 35 31 31 30 30 40 37 37 32 32 4 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! COMPLETED ASSEMBLY 38 30 3. 3. Install handle assembly to lower elevator tubes (32) using bolt (29), spacers (36), and nut (31) as shown. 29 35 31 35 36 36 4 NOTE: Before going on to next step, make sure adjustable system assembly is set to the 10’ (3.05 m) setting. 23 03/06 ID# M661134 ID# M661134 03/06 24 4. Attach upper elevator tubes (35) to backboard support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. 5. Attach lower elevator tubes (32) and counter balance spring (33) to backboard support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. 29 26 26 27 31 33 32 29 32 26 31 25 03/06 ID# M661134 6. Insert T-bolt (55) into rim bracket (54) then, attach that assembly to board using bolts (44) and nuts (14) 14 55 54 54 14 44 Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto b...