Assessments - 2, GPA: 3.5 ( )

Fabricante : Kobe Range Hoods Arquivo Tamanho: 2.54 mb Arquivo Nome : Língua de Ensino:

Refer Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 15 Install Accessories Figure 16 7. Attach oil tunnel. Refer to Figure 16. 8. Refer to Figure 17. Slide the baffle filter into the hood. Push the baffle filter upward. . Slide forward. Pull downward. Fit into place. 9. For bottom casing, repeat above steps. Refer to page 17. 10. Install heating lamps (not included), 120 Volts 175 Watts max. each. Final Assembly 11. Turn power ON in control panel. Check all lights and fan operation. Figure 17 12. Make sure to leave this manual for the homeowner. 11 OPERATION INSTRUCTIONS This KOBE hood is equipped with two rotary controls with powerful centrifugal squirrel cage, baffle filters, and bright 12-volt 20-watt halogen lights. The two rotary controls are Light Control & Speed Control. Refer to Figure 18. Figure 18 Note: For best results, turn hood to QuietMode™ prior to preparation or cooking toestablish airflow in the kitchen. Adjust speed as needed. • Rotate the Speed Control clockwise to cycle from QuietMode™, Low, Medium, High, and Off; and rotate counterclockwise to cycle from High, Medium, Low, QuietMode™, and off • Rotate the Light Control clockwise to cycle the light intensity through low, medium, high, and off. • Press the back Red button to turn on heating lamp. (Note: Heating lamps are sold separately. Heating lamps required 120-volt, 175-watt.) 12 MAINTENANCE For the optimal level of operation, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. 3. DO NOT allow deposits to accumulate or remain on the hood. 4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. 5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth. To Clean Baffle Filters & Oil Tunnel CAUTION: DRAIN BAFFLE FILTERS AND OIL TUNNEL BEFORE OIL WILL OVERFLOW. 1. Remove the baffle filters and oil tunnel. 2. Using a sponge, wash with warm soapy water. Dry completely before returning into place. (Note: Baffle Filters are top rack dishwasher safe.) 13 Replacing Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are off, and range hood is unplugged. 2. Place the flat-headed screwdriver into the groove of the halogen light glass covering and the housing. . 3. Pop out the halogen light glass covering. . 4. Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W maximum. . 5. Using a cloth, hold the new light bulb and push securely into light socket. 6. Return halogen light glass cover to the housing. . 7. Turn range hood ON to test for operation. 14 SPECIFICATIONS MODEL / SIZE CH0330SQB / 30” CH0336SQB / 36" CH0342SQB / 42” CH0348SQB / 48” COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE CH0330SQB – 300W / 2.68A CH0336SQB – 300W / 2.68A CH0342SQB – 320W / 2.86A CH0348SQB – 320W / 2.86A VOLTAGE 120V 60Hz NUMBER OF MOTORS 1 DESIGN 18-Gauge Seamless / Satin Finish FAN TYPE: CENTRIFUGAL Squirrel Cage EXHAUST Top Transition Rectangular to 8” Round CONTROLS Rotary Control HALOGEN LIGHTS 12V 20W x 2 – 30”, 36” 12V 20W x 3 – 42”, 48” HOOD DIMENSION (CH0330SQB) 29-3/4” x 25” x 18” (W x D x H) (CH0336SQB) 35-3/4” x 25” x 18” (CH0342SQB) 41-3/4” x 25” x 18” (CH0348SQB) 47-3/4” x 25” x 18” OPTIONAL ACCESSORIES 1) Original Kit - Duct Cover: (W x D x H) Model No. CH0030DC-12 30” x 12”x 12” Model No. CH0036DC-12 36” x 12”x 12” Model No. CH0042DC-12 42” x 12”x 12” Model No. CH0048DC-12 48” x 12”x 12” 2) Model No. SSP30 30” Stainless Steel Back Panel 30” x 1/10” x 32” 3) Model No. SSP36 36” Stainless Steel Back Panel 36” x 1/10” x 32” Net Gross (CH0330SQB) 66.0 84.0 HOOD WEIGHT (lbs) (CH0336SQB) 73.0 93.0 (CH0342SQB) 84.0 106.0 (CH0348SQB) 90.5 115.0 SPEED QuietMode™ Low Medium Air Capacity (cfm) 400 600 800 Sone* 1.4* 3.5 7.0 *One sone is equivalent to the sound of a refrigerator at 40 decibels. **Specifications subject to change without notice. High 1000 8.0 15 MEASUREMENTS & DIAGRAMS . All measurements in ( ) are millimeters. . All inch measurements are converted from millimeters. Inch me...

Baixe o seu

Para fazer o download, introduza 2 dígitos :