Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Heated air entering the attic will activate the power vent. Figure 3 - Ventilation Air from Outdoors Outlet Air Ventilated Attic Outlet Air Inlet Air Inlet Air Ventilated Crawl Space To Crawl Space To Attic UNPACKING 1. Lift off corrugated box enclosing stove body crating. 2. Remove screws fastening back and top of wood frame enclosure.Two or more people must carefully lift stove up and out of wooden crate. 3. Remove plastic bag from stove body. 4. Remove back panel from stove (see Figure 4). Use an adjustable wrench or a 10 mm socket. Remove four (4) bolts and washers. Keep bolts and washers to reattach back panel later. 5. Remove bubble-wrapped log set, rod and screen from stove. Remove all protective packaging applied for shipment. 6. Check all items for any shipping damage. If damaged, promptly inform dealer where you bought heater. Some fiber flakes may fall from logs. This is acceptable. 7. Place freestanding stove near desired location in room. Top of Wood Frame Enclosure STOVE TOP Back of Wood Frame Enclosure Back Back Panel Panel Screws Screws STOVE BACK Figure 4 - Unpacking Stove from Wooden Shipping Enclosure 111487-01D INSTALLATION IMPORTANT: Vent-free heaters add moisture to the air.Although this is beneficial, installing heater NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heatingsystem, you may run system’s circulating blower while using heater. This will help circulatetheheatthroughoutthe house. In the event of a power outage, you can use this heater as your primary heat source. WARNING: A qualified service person must install heater. Follow all local codes. WARNING: Never install the heater • in a bedroom or bathroom • in a recreational vehicle • where curtains, furniture, clothing or other flammable objects are less than 42 inches from the front, top or sides of the heater • in high traffic areas • in windy or drafty areas CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oilorkerosenelamps,etc.)in the air exist, may discolor walls or cause odors. in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, page 5. CHECK GAS TYPE Use the correct gas type (natural or propane/LP) for your unit. If your stove heater gas type is different from your house gas type, do not install heater. Call dealer where you bought heater for proper type heater. WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted. CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only) WARNING: Maintain the minimum clearances.Ifyoucan, provide greater clearancesfrom floor, ceiling and adjoining side and back walls. Carefully follow the instructions below. This stove is a freestanding unit designed to set directly on the floor. DO NOT place stove directly on carpeting, vinyl tile or any combustible material other than wood. The stove must be set on a metal or wood panel extending the full width and depth of the stove for these floor coverings. Important: You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are shown in Figure 5, page 9. Measure from outermost point of stove top. Minimum Wall and Ceiling Clearances (see Figure 5, page 9) A. Clearances from outermost point of stove top to any combustible side wall should not be less than 12 inches. B. Clearances from outermost point of stove top to any combustible back wall should not be less than 6 inches (includes corner installations). C. Clearances from the stove top to the ceiling should not be less than 48 inches. 111487-01D INSTALLATION CONNECTING TO GAS SUPPLY Continued Front View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Back Wall 6 " Minimum 12 " 12 " Minimum Minimum Side Wall Side Wall Front of Stove Unit Top View Corner Wall Floor Wall 6 " Minimum 6 " Minimum Front of Stove Unit Back Wall Front of Stove Unit Side View Figure 5 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator. WARNING:Aqualified service personmustconnectheatertogas supply. Follow all local codes. CAUTION: Never connect propane/LPheaterdirectlytothe propane/LP supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane/LP supply. WARNING: Never connect naturalgasheatertoprivate(nonutility) gas wells. This gas is commonly known as wellhead gas. Installation Items Needed Before installing heater, make sure you have...
Este manual também é adequado para os modelos :Formadores - CSBNT (1.04 mb)
Formadores - CSBPT (1.04 mb)
Formadores - CSPBPT (1.04 mb)
Formadores - CSPINT (1.04 mb)