Log:
Assessments - 3, GPA: 3.7 ( )

Instruções de Operação Spirit, Modelo XT200

Fabricante : Spirit
Arquivo Tamanho: 633.88 kb
Arquivo Nome :
Língua de Ensino:
Fotos e especificações  Spirit  XT200
Ir para baixar



Facilidade de uso


Pulling this safety tether cord will stop tread-belt movement. To Use: 1. Place the magnet into position on the round metal portion of the console control head. Your treadmill will not start and operate without this. Removing the magnet also secures the treadmill from unauthorized use. 2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The magnet has strong enough power to minimize accidental, unexpected stopping. The clip should be attached securely to make certain it does not come off. Be familiar with its function and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal operation. 5 XT200. / XT 600 / XT 800 XT200. / XT 600 / XT 800 XT200. 7 / XT 600 / XT 800 Assembly Instructions (XT200 / XT600) ASSEMBLY PACK CHECK LIST (XT200 /XT600) (8 pcs) 5/16" x 15m/m Button Head Socket Screw (4 pcs) 5/16" x 2" Button Head Socket Screw (4 pcs) 8 x 23 x 1.5T Curve Washer (2 pcs) 5/16" x 2-3/4" Button Head Socket Screw (2 pcs) 5/16" x 1-1/2" Button Head Socket Screw (4 pcs) 8 x 23 x 1.5T Flat Washer (6 pcs) 3.5x38 m/m Self Tapping Screw (1pc) Safety Key (1 pc) Deck / Belt Lubricant (1 pc) Combination M5 Allen Wrench & Screwdriver (1 pc) M6 Allen Wrench Assembly (XT200 /XT600) Unpack the treadmill and locate the hardware pack. The hardware pack is separated into: one section containing tools and four sections labeled steps 1-4 which contain the hardware needed for assembly of each step. The assembly steps below are numbered one through four and correspond to the hardware in the numbered sections of the hardware pack. Remove only the hardware for the step you are currently assembling to avoid confusion and mix-ups. STEP 1 1. Take the Left and Right upright tubes and slip the upright covers onto the tubes (observe the cover orientation is correct). Connect the Middle Console Cable that exits from the bottom of the right upright tube with the lower Console Cable. Install the Left and Right (L & R) Uprights into the Left and Right Receiving Tubes. Be careful not to pinch the wire when installing the upright. 2. Install and hand tighten the 2pcs of 3/8” x 2” Button Head Socket Screw and 2pcs of 3/8” split washer into the top hole on the sides of the L & R tubes. Then install and hand tighten the 6pcs of 5/16”x 5/8” Button Head Socket Screw in the remaining holes on the sides and front of the L & R tubes. Do not tighten these screws until assembly is complete. 8 XT200. / XT 600 / XT 800 STEP 2 1. Mount the L&R Handle bars onto Handle bar mounting plates at the top of the upright tubes with 4pcs of 5/16” x 2” Button Head Socket Screw and 4pcs of curved washer. NOTE: The L&R handle bars are different. The Right handle bar has two wires and the switches on the handle bar say “Fast and Slow” while the Left handle bar switch says “Up and Down”. STEP 3 1.Install the L & R ...

Este manual também é adequado para os modelos :
Formadores - XT 800 (633.88 kb)
Formadores - XT 600 (633.88 kb)
Formadores - XT800 (633.88 kb)
Formadores - XT200/XT600 (633.88 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias